Paradyne 2600 IP DSLAM About This Guide

2600-A2-GN20-10 January 2004 iii

About This Guide

Document Purpose and Intended Audience

This document is written for technicians who install the BitStorm 2600 IP DSLAM.

Document Summary

A master glossary of terms and acronyms used in Paradyne documen ts is

available on the World Wide Web at www.paradyne.com. Select Support →

Technical Manuals → Technical Glossary.

Section Description

Chapter1, Installation Describes the physical installation of the BitStorm 2600 into

a rack.

Chapter2, Cabling Describes how to install all cables for the BitStorm 2600.

Chapter3, LEDs Ex plains the meaning and usage of the front pa nel LEDs.

Chapter4, Configuration Describes the minimal configuration steps required to

prepare the BitStorm 2600 for remote access, using the

command line interface and web interfac e.

AppendixA, Connec tors

and PinAssignments

Provides pinouts for connectors on the BitStorm 2600.

AppendixB, Equipm ent List Provides part numbers for the BitStorm 2600 and related

products.

AppendixC, Te ch ni ca l

Specifications

Lists the technical characteristics of the BitStorm 2600.

Index Lists key terms, acronyms, concepts, and sections in

alphabetical order.

Contents

Main Page Important Safety Instructions C EMI Notices UNITED STATES EMI NOTICE: CANADA EMI NOTICE: Notices to Users of the Canadian Telephone Network CE Marking Page Page Contents About This Guide 1 Installation 2 Cabling ii 3 LEDs 4 Configuration A Connectors and Pin Assignments B Equipment List C Technical Specifications Index About This Guide Document Purpose and Intended Audience Document Summary iv Related Product Documents Installation 1-2 Preparation Cables Required 1-4 Unpacking the Hardware HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES ! Package Contents Table 1-3. Contents of Hardware Kit Shipped with the BitStorm 2600 Appearance Description Quantity 1-6 Mounting Configurations Mounting Brackets NOTE: Installing the Brackets for Rack Mounting Page 1-8 Installing the BitStorm 2600 Into a Rack 1. Installation 2600-A2-GN20-10 January 2004 1-9 3. Insert and tighten the screws in the top screw positions, then tighten the bottom screws. 03-17436 1-10 Installing the BitStorm 2600 on a Wall Page 1-12 Installing the BitStorm 2600 on a Shelf or Desktop Cabling Cabling Overview 2-2 DSL Ports GigE Uplink (Port 3) 2-4 10/100BaseT Uplink (Port 2) 2600-A2-GN20-10 January 2004 2-5 Chaining BitStorm 2600s Shorter cables may cause data errors. The top unit has Port 3 (eth3) defined as its uplink and is connected to Port 3 of the next unit in the chain using a straight-through 8-position modular cable . The middle unit has Port 2 (eth2) defined as its uplink and is co nnected to Management Port DSL PORTS 1-24 CONSOLE Port 1 03-17446 Console Port Connecting a Terminal or PC to the Console Port 2-8 Connecting a Modem to the Console Port DSL PORTS 1-24 CONSOLE PORT1-10/100BT PORT2-10/100BT PORT3 Alarm Interface CAUTION: 2-10 Ground Connecting to Power Page 2600-A2-GN20-10 January 2004 3-1 LEDs ALARM ALARM STATUS ACT LED Meanings Configuration Conventions Used 4-2 Using the CLI Configure Management Default Gateway Address Configure Management Inband Address The configure management inband address command specifies the IP address of the unit. Configure Management Out-of-Band Address 4-4 BitStorm 2600 Startup Procedure Login Management Modes Startup Procedure for Inband Management Startup Procedure for Out-of-Band Management 4-6 Using the Web Interface System / Users Configuration / Management / SNMP Page A Connectors and Pin Assignments A-2 DSL Ports and POTS Splitter Connectors Port 1 and Port 2 10/100BaseT Connectors Port 3 1000BaseT Connector A-4 Port 3 GigE SFP Connector Port 3s GigE interface is a standard SFP socket. Table A-4. Port 3 GigE Connector Signal Pin Console Port Connector A-6 ALARM Connector B Equipment List Table B-1. BitStorm 2600 Equipment List (1 of 2) Description Model Number B-2 Table B-1. BitStorm 2600 Equipment List (2 of 2) Description Model Number C Technical Specifications C-2 Table C-1. BitStorm 2600 Technical Specifications (2 of 2) Specifications Criteria Index Numerics A B C F G H I J R S T U V