Manuals / Brands / Computer Equipment / Network Card / Paradyne / Computer Equipment / Network Card

Paradyne 2600 IP DSLAM Port 1 and Port 2 10/100BaseT Connectors, Port 3 1000BaseT Connector

1 58

Download 58 pages, 1.76 Mb

A. Connectors and PinAssignments

2600-A2-GN20-10 January 2004 A-3

Port 1 and Port 2 10/100BaseT Connectors

Port 1 and Port 2 are 8-pin unkeyed modular jacks for a 10/100Base interface.

Port 3 1000BaseT Connector

Port 3’s 1000BaseT interface is an 8-pin unkeyed modular jack.

Table A-2. Port 1 and Port 2 Pinouts

Signal Pin

Transmitted Data + 1

Transmitted Data – 2

Received Data + 3

Unused 4

Unused 5

Received Data – 6

Unused 7

Unused 8

97-15449

Pin 1 Pin 8

Table A-3. Port 3 1000BaseT Connector

Signal Pin

Tip 1 1

Ring 1 2

Tip 2 3

Ring 3 4

Tip 3 5

Ring 2 6

Tip 4 7

Ring 4 8

97-15449

Pin 1 Pin 8

Contents

Main Page Important Safety Instructions C EMI Notices UNITED STATES EMI NOTICE: CANADA EMI NOTICE: Notices to Users of the Canadian Telephone Network CE Marking Page Page Contents About This Guide 1 Installation 2 Cabling ii 3 LEDs 4 Configuration A Connectors and Pin Assignments B Equipment List C Technical Specifications Index About This Guide Document Purpose and Intended Audience Document Summary iv Related Product Documents Installation 1-2 Preparation Cables Required 1-4 Unpacking the Hardware HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES ! Package Contents Table 1-3. Contents of Hardware Kit Shipped with the BitStorm 2600 Appearance Description Quantity 1-6 Mounting Configurations Mounting Brackets NOTE: Installing the Brackets for Rack Mounting Page 1-8 Installing the BitStorm 2600 Into a Rack 1. Installation 2600-A2-GN20-10 January 2004 1-9 3. Insert and tighten the screws in the top screw positions, then tighten the bottom screws. 03-17436 1-10 Installing the BitStorm 2600 on a Wall Page 1-12 Installing the BitStorm 2600 on a Shelf or Desktop Cabling Cabling Overview 2-2 DSL Ports GigE Uplink (Port 3) 2-4 10/100BaseT Uplink (Port 2) 2600-A2-GN20-10 January 2004 2-5 Chaining BitStorm 2600s Shorter cables may cause data errors. The top unit has Port 3 (eth3) defined as its uplink and is connected to Port 3 of the next unit in the chain using a straight-through 8-position modular cable . The middle unit has Port 2 (eth2) defined as its uplink and is co nnected to Management Port DSL PORTS 1-24 CONSOLE Port 1 03-17446 Console Port Connecting a Terminal or PC to the Console Port 2-8 Connecting a Modem to the Console Port DSL PORTS 1-24 CONSOLE PORT1-10/100BT PORT2-10/100BT PORT3 Alarm Interface CAUTION: 2-10 Ground Connecting to Power Page 2600-A2-GN20-10 January 2004 3-1 LEDs ALARM ALARM STATUS ACT LED Meanings Configuration Conventions Used 4-2 Using the CLI Configure Management Default Gateway Address Configure Management Inband Address The configure management inband address command specifies the IP address of the unit. Configure Management Out-of-Band Address 4-4 BitStorm 2600 Startup Procedure Login Management Modes Startup Procedure for Inband Management Startup Procedure for Out-of-Band Management 4-6 Using the Web Interface System / Users Configuration / Management / SNMP Page A Connectors and Pin Assignments A-2 DSL Ports and POTS Splitter Connectors Port 1 and Port 2 10/100BaseT Connectors Port 3 1000BaseT Connector A-4 Port 3 GigE SFP Connector Port 3s GigE interface is a standard SFP socket. Table A-4. Port 3 GigE Connector Signal Pin Console Port Connector A-6 ALARM Connector B Equipment List Table B-1. BitStorm 2600 Equipment List (1 of 2) Description Model Number B-2 Table B-1. BitStorm 2600 Equipment List (2 of 2) Description Model Number C Technical Specifications C-2 Table C-1. BitStorm 2600 Technical Specifications (2 of 2) Specifications Criteria Index Numerics A B C F G H I J R S T U V