Manuals / Paradyne / Computer Equipment / Network Router

Paradyne 4800 Express manual Preparation, „ Installation Site, „ Installation Options, „ Power

Models: 4800 Express

1 52

Download 52 pages 57.01 Kb

Page 12

1. Installation

Preparation

Consider the following before installing the BitStorm 4800 Express IP DSLAM:

Installation Site

Your installation site should be well ventilated, clean, and free of environmental extremes.

Installation Options

The BitStorm 4800 Express may be:

—Mounted with the included mounting brackets in a standard 19-inch

(483 mm) or 23-inch (584 mm) rack (including both Bay Networks and Nortel 23-inch racks), or, with separately purchased mounting brackets, in a 21-inch (535 mm) ETSI rack. ETSI brackets are available from Paradyne. See Appendix B, Equipment List.

As many BitStorm 4800 Express units may be mounted in a standard rack as there are 1.75-inch (44.45 mm) spaces in the rack, so long as adequate cooling is provided.

—Mounted vertically against a wall.

The standard mounting brackets provided can be fastened to the base of the unit for wall mounting.

—Set on a shelf or desktop.

Up to five BitStorm 4800 Express units may be stacked on a shelf or desktop.

Power

The BitStorm 4800 Express operates from a 90 to 265 VAC, 47 to 63 Hz power source.

Cabling

No cable except the power cable is provided with the BitStorm 4800 Express. See Table 1-2, Cable Descriptions, to determine what cables you need to procure before installation.

1-2

July 2004

4821-A2-GN21-10

Image 12

Paradyne 4800 Express manual Preparation, „ Installation Site, „ Installation Options, „ Power, „ Cabling

Contents

Model 4821-A2 Installation Guide BitStorm 4800 ExpressDocument No. 4821-A2-GN21-10 JulyWarranty, Sales, Service, and Training Information Copyright 2004 Paradyne Corporation All rights reservedPrinted in U.S.A Document FeedbackSoftware and Firmware License Agreement Important Safety Instructions EMI Notices UNITED STATES - EMI NOTICE CANADA - EMI NOTICENotices to Users of the Canadian Telephone Network CE MarkingJapan Contents 1 InstallationAbout This Guide 2 Cabling4 Configuration A Connectors and Pin AssignmentsB Equipment List C Technical Specifications Index About This Guide Document Purpose and Intended AudienceDocument Summary Chapter 1, InstallationRelated Product Documents Document NumberDocument Title 4821-A2-GB21Installation Table 1-1. BitStorm 4800 Express Models and FeaturesOverview Model Number„ Installation Site „ Installation Options„ Power PreparationConnector Name Connector and CableFor Connecting Cables RequiredPackage Contents HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICESUnpacking the Hardware Appearance DescriptionQuantity Mounting Configurations ProcedureInstalling the Brackets for Rack Mounting Three basic installation configurations are available23-inch 584 mm EIA and Bay Networks 23-inch 584 mm NortelInstalling the BitStorm 4800 Express Into a Rack ProcedureALARM 04-17526CONSOLE DSL PORTS DSL PORTSInstalling the BitStorm 4800 Express on a Wall 1-10Procedure 1-11 17.85 in 453 mmInstalling the BitStorm 4800 Express on a Shelf or Desktop 1-12Procedure „ 10/100BaseT Uplink Port 2 on page „ Management Port on page „ Connecting to Power on pageCabling Cabling OverviewDSL Ports Procedure10/100BaseT Uplink Port ProcedureManagement Port ProcedureEthernet Switch PortConnecting a Terminal or PC to the Console Port Console PortProcedure Connecting a Modem to the Console Port ProcedureGround Procedure2. Remove the screw marked by the ground symbol 3. Fasten the ring terminal to the front panel using the same screwConnecting to Power ProcedureLEDs LED LocationsFigure 3-1. Front Panel LEDs PORT1 PORT2 CONSOLE 10/100BT 10/100BT TEST ALARMLED Meanings Table 3-1. Front Panel LEDsColor StateConfiguration OverviewUsing the CLI Configure Management Default Gateway AddressTable 4-1. CLI Commands CommandConfigure Management Inband Address Configure Management Out-of-Band Addressconfigure management inband address ipaddress subnetmask PDYN# configure management inband address 137.90.127.3BitStorm 4800 Express Startup Procedure LoginManagement Modes ProcedureStartup Procedure for Inband Management Startup Procedure for Out-of-Band ManagementProcedure ProcedureUsing the Web Interface ProcedureSystem / Users ProcedureConfiguration / Management / SNMP ProcedureConnectors and Pin Assignments „ DSL Ports Connectors on page A-2„ Port 1 and Port 2 10/100BaseT Connectors on page A-3 „ Console Port Connector on page A-4DSL Ports Connectors Table A-1. DSL Connector PinoutsConnector Pins DSL PortPort 1 and Port 2 10/100BaseT Connectors SignalTable A-2. Port 1 and Port 2 Pinouts Console Port Connector Table A-3. Console Port ConnectorRS-232 Signal DirectionEquipment List Table B-1. BitStorm 4800 Express Equipment ListDescription Model NumberB. Equipment List July4821-A2-GN21-10 Technical Specifications Table C-1. BitStorm 4800 Express Technical SpecificationsSpecifications CriteriaC. Technical Specifications July4821-A2-GN21-10 Index NumericsIN-1 Page IN-3 IN-4 IndexJuly 4821-A2-GN21-10