Rack Mount G.SHDSL Modem Card
USER MANUAL
MODEL 3088RC
RocketLink-G NTU
Warranty Information
Configuration
General Information
Connect Twisted Pair 120 ohm to G.703/G.704 Network
Installation
Operation
Connecting the Model 3088RC/D/V X.21 to a “DCE” or “DTE” de
Model 3088RC Interface Pin Assignments
Specifications
PSTN Regulatory
1.0 WARRANTY INFORMATION
Safety Compliance
1.1 COMPLIANCE EMC Compliance
1.3 RADIO AND TV INTERFERENCE FCC PART
1.2 FCC PART 68 ACTA STATEMENT
1.5 CE DECLARATION OF CONFORMITY
1.4 INDUSTRY CANADA NOTICE
D R M Green European Compliance Services Limited
1.7 SERVICE
1.6 AUTHORIZED EUROPEAN REPRESENTATIVE
Tel +1 301 Email support@patton.com
the device first
1.8 SAFETY WHEN WORKING WITH ELECTRICITY
2.1 FEATURES
2.0 GENERAL INFORMATION
2.2 DESCRIPTION
3088RC/D/V/V provides a X.21 interface on a DB-15 female connector
2.3 SERIAL INTERFACE TYPES
3088RC/A/I provides a V.35 interface on an M/34 female connector
3088RC/C/AI provides a Ethernet interface on an RJ45 connector
3.0 CONFIGURATION
3.1 ABOUT SOFTWARE CLI CONFIGURATION
3.2 ABOUT HARWARE DIP SWITCH CONFIGURATION
Position
3.3 CONFIGURING THE DIP SWITCHES V.35, X.21, and Ethernet Models
Position
Function
S1-3
S1-1 through S1-7 Data Rate
S1-1
S1-2
S1-4
S1-1
S1-2
S1-3
S1-8 TX Clock
Setting
S2-1 Front Panel Switches
Front Panel Switches
S2-5
S2-4 through S2-5 Clock Mode
Clock Mode
S2-4
S2-7 DTE Interface Type
3.4 ABOUT SYSTEM RESET MODE
S2-6 DTE Loops
S2-6
Software Upgrades
ConÞguration Reset to Factory Defaults
3.5 CONFIGURING THROUGH THE CONSOLE
DSL Error Monitor Interval Time The length in seconds of an interval
DSL Link State In Progress, Success, Deactivated, or Idle
DSL Sync State Out of Sync, Acquiring Sync, In Sync, or Losing Sync
DSL Line Condition Good or Poor
Console Help Commands
System ConÞguration Commands
system set password password Sets the system password
system set circuitid circuitid Sets the circuit ID
DSL Error Monitor
System Status Commands
DSL ConÞguration Commands
dsl set lineprobe enableddisabled Enable or disable line probe
DSL Status Command
DSL Clear Errcntrs Command
dsl set errmon inttime inttime Sets the length of each interval
Position 1&2
3.6 CONFIGURING THE V.35 REAR CARD
Model 1001RCM13445 & 1001RCM134TB Strap Settings
Strap
Strap
3.7 CONFIGURING THE X.21 REAR CARD
Model 1001RCM11545& 1001RCM115TB Strap Settings
Description
Line Coding Options
3.8 CONFIGURING THE E1 REAR CARD
DIP Switch ConÞguration
Line Framing & Coding
S1-3
Option
Jumper ConÞguration
S1-2
Making Interface Connections
Figure 4. K Module Rear Panels, Showing Location of Connectors
Figure 5. 120 ohm RJ-48C G.703/G.704 Interface
Figure 6. 75 ohm Dual Coaxial G.703 Interface
Note The 3088RC/C/AI only supports synchronous speeds
3.9 CONNECTING THE ETHERNET REAR CARD
Figure 7. Driver Board mounted on Model 3088RC
Connecting the Interface Driver Board
Connecting to the 10Base-T Ethernet Port
Figure 9. Model 3088RC Ethernet Connector Pinout
Figure 8. 3088RC/C/AI Ethernet Port
Page
LED Status Monitors
Figure 10. RJ-45 Line Interface
Figure 11. 3088RC Rear Panel, LED Locations
5 pulses = WAN receive frames too large
1 pulse = system status ok
2 pulses = No MAC entries in the MAC address table
4 pulses = IMRC2/IA buffer is saturated
more information
4.0 INSTALLATION
The Rack Power Supply
4.1 THE MODEL 1001R14 RACK CHASSIS
4.2 INSTALLING MODEL 3088RC SERIES INTO THE CHASSIS
Powering Up Your 1001R14 Rack
4.3 CONNECTING THE TWISTED PAIR INTERFACE
X.21, female DB-15
Figure 13. Model 3088RC V.35/X.21 interfaces
3088RC/D/V
3088RC/A/I
Straight-Through Cable
4.4 CONNECTING THE MODEL 3088RC/A/I V.35 SERIAL INTER FACE
Connecting the Model 3088RC/A/I V.35 to a “DTE” device
DSL Span
Model 3088RC/A DCE
Connecting the Model 3088RC/A/I V.35 to a “DCE” device
Remote Model 3088RC DSL Span G.703 E1 NTU
Tail-circuit cable
Figure 16. Connecting the Model 3088RC/D/V to X.21 DTE or DCE
4.5 CONNECTING THE MODEL 3088RC/D/V X.21 SERIAL INTER FACE
Connecting the Model 3088RC/D/V X.21 to a “DCE” or “DTE” device
The interconnecting cables shall be acceptable for
4.7 CONNECTING THE 3088RC/C/AI ETHERNET INTERFACE
4.6 CONNECTING THE 3088RC/K/K E1 INTERFACE
Power
5.1 LED STATUS INDICATORS
5.0 OPERATION
Color
Figure 19. Local Analog Loopback Diagram
5.2 TEST MODES
Loopbacks
Figure 18. 3088RC Block Diagram
Patterns
5.3 REMOTE CONSOLE OPERATION
Establishing a Remote Console Session
4. At the command prompt, enter the command remote console
Figure 22 is a screenshot of opening a typical remote console session
Figure 23. Remote control session with LAL diagram
Differences in Local and Remote Control Session Behavior
to communicate with the far-end 3088RC
5.4 SOFTWARE UPGRADE
5.5 RESET CONFIGURATION TO FACTORY DEFAULT
A.1 CLOCKING MODES
A.4 SERIAL CONNECTOR
A.5 DIAGNOSTICS
APPENDIX A
A.10 LINE RATES DSL LINE
A.7 CONFIGURATION
A.8 TRANSMISSION LINE
A.9 LINE CODING
Pin #
Signal
APPENDIX B
B.1 RJ-11 NON-SHIELDED DSL PORT
Signal
B.3 E1 INTERFACE
B.4 X.21 INTERFACE
Signal
Signal Ground
B.5 RS-232 CONSOLE INTERFACE
RJ-45 non-shielded connector EIA-561
Signal
Page
Page
Copyright 2008 Patton Electronics Company All Rights Reserved