RocketLink-G NTU
USER MANUAL
MODEL 3088RC
Rack Mount G.SHDSL Modem Card
Warranty Information
Configuration
General Information
Connecting the Model 3088RC/D/V X.21 to a “DCE” or “DTE” de
Installation
Operation
Connect Twisted Pair 120 ohm to G.703/G.704 Network
Specifications
Model 3088RC Interface Pin Assignments
1.1 COMPLIANCE EMC Compliance
1.0 WARRANTY INFORMATION
Safety Compliance
PSTN Regulatory
1.2 FCC PART 68 ACTA STATEMENT
1.3 RADIO AND TV INTERFERENCE FCC PART
1.4 INDUSTRY CANADA NOTICE
1.5 CE DECLARATION OF CONFORMITY
Tel +1 301 Email support@patton.com
1.7 SERVICE
1.6 AUTHORIZED EUROPEAN REPRESENTATIVE
D R M Green European Compliance Services Limited
1.8 SAFETY WHEN WORKING WITH ELECTRICITY
the device first
2.1 FEATURES
2.0 GENERAL INFORMATION
2.2 DESCRIPTION
3088RC/C/AI provides a Ethernet interface on an RJ45 connector
2.3 SERIAL INTERFACE TYPES
3088RC/A/I provides a V.35 interface on an M/34 female connector
3088RC/D/V/V provides a X.21 interface on a DB-15 female connector
3.0 CONFIGURATION
3.1 ABOUT SOFTWARE CLI CONFIGURATION
3.2 ABOUT HARWARE DIP SWITCH CONFIGURATION
Function
3.3 CONFIGURING THE DIP SWITCHES V.35, X.21, and Ethernet Models
Position
Position
S1-2
S1-1 through S1-7 Data Rate
S1-1
S1-3
S1-3
S1-1
S1-2
S1-4
Front Panel Switches
Setting
S2-1 Front Panel Switches
S1-8 TX Clock
S2-4
S2-4 through S2-5 Clock Mode
Clock Mode
S2-5
S2-6
3.4 ABOUT SYSTEM RESET MODE
S2-6 DTE Loops
S2-7 DTE Interface Type
Software Upgrades
ConÞguration Reset to Factory Defaults
3.5 CONFIGURING THROUGH THE CONSOLE
DSL Error Monitor Interval Time The length in seconds of an interval
DSL Link State In Progress, Success, Deactivated, or Idle
DSL Sync State Out of Sync, Acquiring Sync, In Sync, or Losing Sync
Console Help Commands
DSL Line Condition Good or Poor
System ConÞguration Commands
system set password password Sets the system password
system set circuitid circuitid Sets the circuit ID
dsl set lineprobe enableddisabled Enable or disable line probe
System Status Commands
DSL ConÞguration Commands
DSL Error Monitor
DSL Status Command
DSL Clear Errcntrs Command
dsl set errmon inttime inttime Sets the length of each interval
Strap
3.6 CONFIGURING THE V.35 REAR CARD
Model 1001RCM13445 & 1001RCM134TB Strap Settings
Position 1&2
Description
3.7 CONFIGURING THE X.21 REAR CARD
Model 1001RCM11545& 1001RCM115TB Strap Settings
Strap
Line Framing & Coding
3.8 CONFIGURING THE E1 REAR CARD
DIP Switch ConÞguration
Line Coding Options
S1-2
Option
Jumper ConÞguration
S1-3
Making Interface Connections
Figure 4. K Module Rear Panels, Showing Location of Connectors
Figure 5. 120 ohm RJ-48C G.703/G.704 Interface
Figure 6. 75 ohm Dual Coaxial G.703 Interface
3.9 CONNECTING THE ETHERNET REAR CARD
Note The 3088RC/C/AI only supports synchronous speeds
Connecting the Interface Driver Board
Figure 7. Driver Board mounted on Model 3088RC
Connecting to the 10Base-T Ethernet Port
Figure 9. Model 3088RC Ethernet Connector Pinout
Figure 8. 3088RC/C/AI Ethernet Port
Page
LED Status Monitors
Figure 10. RJ-45 Line Interface
Figure 11. 3088RC Rear Panel, LED Locations
4 pulses = IMRC2/IA buffer is saturated
1 pulse = system status ok
2 pulses = No MAC entries in the MAC address table
5 pulses = WAN receive frames too large
4.1 THE MODEL 1001R14 RACK CHASSIS
4.0 INSTALLATION
The Rack Power Supply
more information
Powering Up Your 1001R14 Rack
4.2 INSTALLING MODEL 3088RC SERIES INTO THE CHASSIS
4.3 CONNECTING THE TWISTED PAIR INTERFACE
3088RC/A/I
Figure 13. Model 3088RC V.35/X.21 interfaces
3088RC/D/V
X.21, female DB-15
DSL Span
4.4 CONNECTING THE MODEL 3088RC/A/I V.35 SERIAL INTER FACE
Connecting the Model 3088RC/A/I V.35 to a “DTE” device
Straight-Through Cable
Tail-circuit cable
Connecting the Model 3088RC/A/I V.35 to a “DCE” device
Remote Model 3088RC DSL Span G.703 E1 NTU
Model 3088RC/A DCE
The interconnecting cables shall be acceptable for
4.5 CONNECTING THE MODEL 3088RC/D/V X.21 SERIAL INTER FACE
Connecting the Model 3088RC/D/V X.21 to a “DCE” or “DTE” device
Figure 16. Connecting the Model 3088RC/D/V to X.21 DTE or DCE
4.6 CONNECTING THE 3088RC/K/K E1 INTERFACE
4.7 CONNECTING THE 3088RC/C/AI ETHERNET INTERFACE
Color
5.1 LED STATUS INDICATORS
5.0 OPERATION
Power
Figure 18. 3088RC Block Diagram
5.2 TEST MODES
Loopbacks
Figure 19. Local Analog Loopback Diagram
Patterns
5.3 REMOTE CONSOLE OPERATION
Establishing a Remote Console Session
4. At the command prompt, enter the command remote console
Figure 22 is a screenshot of opening a typical remote console session
Differences in Local and Remote Control Session Behavior
Figure 23. Remote control session with LAL diagram
5.4 SOFTWARE UPGRADE
to communicate with the far-end 3088RC
5.5 RESET CONFIGURATION TO FACTORY DEFAULT
APPENDIX A
A.4 SERIAL CONNECTOR
A.5 DIAGNOSTICS
A.1 CLOCKING MODES
A.9 LINE CODING
A.7 CONFIGURATION
A.8 TRANSMISSION LINE
A.10 LINE RATES DSL LINE
B.1 RJ-11 NON-SHIELDED DSL PORT
Signal
APPENDIX B
Pin #
Signal
B.3 E1 INTERFACE
B.4 X.21 INTERFACE
Signal
Signal
B.5 RS-232 CONSOLE INTERFACE
RJ-45 non-shielded connector EIA-561
Signal Ground
Page
Page
Copyright 2008 Patton Electronics Company All Rights Reserved