B.If the setting temperature is lower than or equal to the room temperature, the temperature display will flash and the unit will stop heating. When the room temperature falls down to less than the setting temperature, the unit will

resume heating. The heater will cycle on and off this way to maintain the setting temperature.

Note: Every time you turn on the heater, the heater will heat forcedly for 2 minutes. After that the heater will work based on the below instruction. And when the room temperature reaches the setting temperature or the setting temperature is lower or equal to the room temperature, the heating element will shut off immediately, but the fan motor will continue running for 1030 seconds before shutting off. This is a safety feature to protect the unit from being too hot.

Timer setting: This heater has an 8 hours On/Off timer. You can set an “ On” timer when the heater is standing by (plugged in but not working) or you can set an “ Off”

timer when the heater is working. For example, you can plug in the heater and set the timer to turn the heater on after 3 hours, you can also set the timer to turn the heater off after 6 hours and a half when the heater is working.

Example for “ On” Timer:

1.When the heater is plugged in and not working, press the “ C” Timer and the “ A” Digital Indicator will display the last set value (0.0 is the default set). Press the “ Up” or “ Down” key to choose your desired timer setting. The timer will increase or decrease half on hour every time you press the “ Up” or “ Down” key and goes up and down from 0.0 to 8.0.

2.Press “ Up” key 6 times until 3.0 is displayed, press the “ C” Timer again to confirm the set. Now your heater is set to be turned on after 3 hours.

Example for “ Off” Timer:

1.When the heater is working, press the “ C” Timer.

2.Press “ Up” key 13 times or “ Down” key 3 times until 6.5 is displayed, press the “ C” Timer

again to confirm the set.

Now your heater is set to be turned off after 6 hours and a half. To disable the timer, adjust the set value of the timer to 0.0.

Note: Once the timer is set, the heater will work this way unless you unplug the heater. You have to reset the timer every time you plug in your heater.

Remote control (Refer to Fig 2): This heater has a 6 key remote with the following function (See picture above):

1.ON/OFF: Power switch key, used to turn off the heater when the heater is on.

2.OSC: Oscillation switch, used to enable the oscillation function by pressing once. To disable the oscillation function, press the “OSC” key once more. This key is only valid when the heater is on (Hi, Low or Fan).

3.TIMER: Timer setting key, used to enable the timer setting or confirm the setting value.

4.MODE: Mode select key, used to switch the heater circularly in sequence of HI -LO - FAN when the heater is on.

5.“ +” and -: Value adjustment key, used to adjust the set value of the temperature or

the timer.

CAUTION: This heater includes an Overheat Protection System that shuts the unit off if it overheats due to abnormal conditions. If this occurs turn the heater “OFF”, unplug it, and inspect and remove any objects on or adjacent to the heater. Allow it to cool for a few minutes, plug it back in, and resume normal operation.

ADDITIONAL FEATURES

This heater has additional features:

Dual LED display-Allowsyou to adjust the heater and check the set value at the same time in a distance (Within16 ft of the heater), you can also check the status of the heater easier.

Convenient Carry Handle-Allowsfor easy maneuvering from room to room.

TROUBLESHOOTING

If your heater fails to operate, please follow these instructions:

Ensure that your circuit breaker or fuse is working properly.

Be sure the heater is plugged in and that the electrical outlet is working properly.

Check for any obstruction. If you find any obstruction, turn the heater “OFF”. Unplug the heater and wait a few minutes for it to cool down. Carefully remove the obstruction. Plug the heater in and turn it on again by referring to the OPERATING INSTRUCTIONS.

NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HEATER, PLEASE SEND YOUR HEATER TO AN AUTHORISED SERVICE CENTER FOR MAINTENCE. PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HEATER YOURSELF. DOING SO MAY VOID THE WARRANTY AND COULD CAUSE DAMAGE OR PERSONAL INJURY.

CLEANING AND STORAGE

It is recommended that the heater be cleaned at least one time during the operating season in order to provide the optimum level of performance. ALWAYS TURN THE POWER SWITCH OFF AND UNPLUG THE HEATER BEFORE CLEANING. Be sure to save the box for off- season storage.

Turn the heater “ OFF” , unplug it and wait for the heater to cool down.

Use a dry cloth to clean only external surfaces of the heater.

Do not use any cleaning agents or detergents.

Never immerse the heater in water.

Pack the heater in the original carton and store it in a cool and dry place.

SPECIFICATIONS

Model No.: HC-0119A

Voltage: 120V, 60Hz

Current: Maximum continuous draw: 12.5 Amps.

Power: LO = 900 Watts, HI = 1500 Watts.

Tolerances on all specifications: Approximately +5%, -10%.

Page 3
Image 3
Pelonis HC-0119A owner manual Additional Features, Troubleshooting, Cleaning and Storage, Specifications

HC-0119A specifications

The Pelonis HC-0119A is a powerful and efficient space heater designed to provide quick warmth during cold months. With its compact design, it is ideal for both home and office use, allowing users to effectively heat small to medium-sized rooms without consuming excessive energy or space.

One of the standout features of the Pelonis HC-0119A is its advanced heating technology, which includes a ceramic heating element. This technology not only heats up quickly but also provides consistent warmth, ensuring that users feel comfortable without waiting long periods for the heater to reach its desired temperature. The ceramic element, known for its durability and efficiency, allows the heater to operate quietly, making it a suitable option for bedrooms, living rooms, and work environments.

The Pelonis HC-0119A is equipped with adjustable thermostat settings, giving users the flexibility to customize their heating preferences according to personal comfort levels. The unit features multiple heat settings, including low, high, and eco modes, which help optimize energy use while maintaining a cozy atmosphere. The eco mode is particularly beneficial for those looking to reduce their energy consumption, as it automatically adjusts the heating output based on the room's temperature.

Safety is a top priority with the Pelonis HC-0119A, and several built-in safety features reflect this commitment. The unit includes an overheat protection mechanism that automatically shuts off the heater if it gets too hot, preventing potential fire hazards. Additionally, the heater is designed with a tip-over switch that ensures it will turn off if accidentally knocked over, giving users peace of mind while they enjoy its warmth.

The lightweight nature of the Pelonis HC-0119A makes it easy to transport from one room to another, and its sleek, modern design allows it to blend seamlessly with various interior styles. The integrated carrying handle further enhances portability, allowing users to maneuver it effortlessly as needed.

In summary, the Pelonis HC-0119A is a reliable, energy-efficient space heater that combines advanced heating technology with user-friendly features and safety mechanisms. Its compact design, multiple heat settings, and emphasis on safety make it an excellent choice for anyone seeking warmth and comfort in their living or working spaces. Whether you need a quick heat boost or a longer-lasting warmth solution, the Pelonis HC-0119A is well-suited to meet diverse heating needs.