![](/images/new-backgrounds/1231645/2316457x1.webp)
IMPORTANT SAFETY INSTRUCTIONS
Read before operating equipment
E n g l i s h
1.Read these instructions.
2.Keep these instructions.
3.Heed all warnings
4.Follow all instructions.
5.Do not use this apparatus near water.
6.Clean only with a dry cloth.
7.Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat
9.Do not defeat the safety purpose of the polarized or
grounding type plug has two blades and third grounding prong. The wide blade or third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet
10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus
11.Only use attachments/accessories specified by the manufacturer.
12.Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination to avoid injury from
13.Unplug this apparatus during lightning storms or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
15.This product may contain lead or mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org.
16.Damage Requiring Service The appliance should be serviced by qualified service personnel when :
A. The power supply cord or the plug has been damaged; or
B.Objects have fallen, or liquid has been spilled into the appliance; or
C.The appliance has been exposed to rain; or
D.The appliance does not appear to operate normally or exhibits a marked change in performance; or
E.The appliance has been dropped, or the enclosure damaged.
17.Tilt/Stability All televisions must comply with recommended international global safety standards for tilt and stability properties of its cabinets design.
•Do not compromise these design standards by applying excessive pull force to the front, or top, of the cabinet which could ultimately overturn the product.
•Also, do not endanger yourself, or children, by placing electronic equipment/toys on the top of the cabinet. Such items could unsuspectingly fall from the top of the set and cause product damage and/or personal injury.
18.Wall or Ceiling Mounting The appliance should be mounted to a wall or ceiling only as recommended by the manufacturer.
19.Power Lines An outdoor antenna should be located away from power lines
20.Outdoor Antenna Grounding If an outside antenna is connected to the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code, ANSI/NFPA No.
21.Objects and Liquid Entry Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings
a)Warning: To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases should not be placed on this apparatus.
22.Battery Usage CAUTION To prevent battery leakage that may result in bodily injury, property damage, or damage to the unit:
•Install all batteries correctly, with + and - alignment as marked on the unit.
•Do not mix batteries (old and new or carbon and alkaline, etc.)
•Remove batteries when the unit is not used for a long time
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE (NEC)
GROUND CLAMP | ANTENNA LEAD IN WIRE |
| |
| ANTENNA DISCHARGE UNIT |
| (NEC SECTION |
| GROUNDING CONDUCTORS |
| (NEC SECTION |
| GROUND CLAMPS |
ELECTRIC SERVICE EQUIPMENT | POWER SERVICE GROUNDING |
ELECTRODE SYSTEM | |
| (NEC ART 250, PART H) |
Note to the CATV system installer: this reminder is provided to call the CATV system installer’s attention to Article
EN 3