Philips 42MD459B user manual TV Functions, 5Initial Setup, Before you begin

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

TV Functions

INTRODUCTION

5Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and autoprogram, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure the unit is connected to antenna or cable.

1After making all the necessary connections, press [POWER y] to turn on the unit.

• This operation may take a few moments.

2Use [Cursor K/L] to select the on-screen language from the choices on the right side of the TV screen. (English / Español / Français)

InitialI iti l Setupt

or	Select the language for setup display.		English
	Elija el idioma de ajuste.		Español
	Sélectionner langue écran config.		Français
	Select	OK OK	MENU
			Skip

•“Initial Setup” menu on step 3 will be displayed in the selected language after you press [OK].

3Use [Cursor K/L] to select “Antenna” for TV channels or “Cable” for CATV channels, then press [OK].

	InitialI iti l Setupt
or	Make sure the antenna is connected to ''ANT. IN'' jack.			Antenna
	Select your signal source.
				Cable
				Skip
	Antenna		Or
	Cable			ANT.IN
	Select	OK OK	BACK	MENU
			Back	Skip

• “Autoprogram” will begin.

InitialI iti l Setupt

Now the system is scanning for channels, please wait.

Auto programming will take up to 20 minutes to complete.

0%

Analog channels	0ch
Digital channels	0ch

MENU

Skip

							PREPARATION
			Select “Retail” or “Home” for your location.
4 Use [Cursor s/ B] to select the desired location setting,
	then press [OK].
			InitialI iti l Setupt
	or
							WATCHING
				Retail		H o m e
				Select		OK OK
	• Select ”Retail”, the unit will be set up with predefined
	setting for retail displays. In this setting, the power						TV
	consumption may possibly exceed the limited
	requirement of the ENERGY STAR® qualification.
	• Select ”Home”, the unit is set to maximize the energy						OPTIONAL
	efficiency for home setting and it can be adjusted
	through a choice of picture and sound quality
	according to your preference.						SETTING
	• When the initial setup is completed, the lowest
	memorized channel with the confirmation message
	of the location setting will be displayed on the TV
	screen.
							OPERATING
	Note:
	• If you connect the cable system directly, contact the CATV
	installer.						BLU-RAY
	• If you press [POWER y] or [MENU / EXIT] during
	autoprogram, this setting will be canceled.
	• The initial autoprogram function can be executed for either
	“Antenna” or “Cable” only once. When you change the
	connection (Antenna / Cable), set autoprogram again.						BLU-RAY
	(Refer to page 22.)
	• If there is no signal input from the antenna terminal and
	no operation for several seconds after you turn on the unit,
	“Helpful Hints” appears. Follow the instructions listed on the						SETTING
	TV screen.
		InitialI iti l Setupt
		No channel is registered.			Retry
					Later
		Try Autoprogram again?					TROUBLESHOOTING
		Verify that you have a cable connected to the "ANT. IN" jack on the
		back panel of the TV, the cannel installation process searches this
		connection. If you are using a cable or satellite box please confirm
		the input to which you have connected the box and use "SOURCE"
		key on the remote control to tune to the appropriate source input.
				MENU	Skip
		Select OK OK
	• You must set ”Home” in step 4. Otherwise, the settings
	of picture and sound quality you adjusted will not be
	memorized after you turn off the unit.
	refer to “Autoprogram” on page 22.						INFORMATION
	After an initial setup is completed...
	• If you want to scan the channels automatically again,
	• You can add the desired channels unmemorized by
	“Autoprogram”. Refer to “Add Channels” on page 23.
	• If you want to change to another language, refer to
	“Language Selection” on page 24.
	• If you want to change the location setting, refer to
	“Location” on page 35.

17

EN