Philips 55PP9502, 60PP9502 manual Connecting a VCR, Rear of TV

Connecting Accessory Devices to Your TV

The TV’s audio/video (AV) input jacks provide for direct picture and sound connections

between the TV and accessory devices such as VCRs, DVD players, and others that have AV out- put jacks.

This example, which uses the INPUT-AV 1 jacks, shows you one way you can connect a VCR to your TV.

Refer to the directions-for-use manual for your VCR for further information on connections.

To make the connections shown in this example, you will need:

•one coaxial cable (75Ω )

•one cable for a video connection (standard RCA connector)

•two cables for audio connections (standard RCA connectors) (only one cable is needed for a nonstereo VCR).

NOTE: The cables are not supplied with your TV. You should be able to buy them at most stores that sell electronics. Or you can call our Customer Care Center at 1-800-531-0039.

BEGIN

CONNECTING A VCR

ANTENNA IN 75Ω	2	AMP SWITCH			Rear of TV
		EXT	INT
	+		_
					HD INPUT-AV 5
				DVI
3	CENTER CHANNEL AMP INPUT
					HD INPUT-AV 4
			4 INPUT-AV 2		G/Y
	INPUT-AV 1			SUBWOOFER	R/Pr
		Y			B/Pb
	VIDEO		VIDEO
	S-		S-VIDEO
	L	Pb	L
					V
										Coaxial Cable
	L		L		L		L
					SYNC
	AUDIO	Pr	AUDIO		AUDIO	AUDIO				Lead-in from
					H
	R		R		R		R			Cable TV Company
Rear of VCR*						1			or VHF/UHF Antenna
										ANT
						OUT	R			IN
						VIDEO				OUT
						OUT		INCH3CH4

*(Example: Philips VCR model VR674CAT)

1 Connect a cable TV or antenna signal to the ANT IN jack on the rear of the VCR.

2 Connect from the OUT jack on the rear of the VCR to the ANTENNA IN 75Ω jack on the rear of the TV.

3 Connect the VIDEO OUT jack on the rear of the VCR to the INPUT AV1 VIDEO jack on the rear of the TV.

4 Connect the audio output R(ight) and L(eft) jacks on the rear of the VCR to the INPUT-AV 1 AUDIO jacks on the rear of the TV.

NOTE: If the VCR is a mono (nonstereo) unit, connect only the left audio cable, which usually has a white connector.

5 Press the AV button on the remote con- trol as many times as necessary to select the AV1 source.

6 Turn the VCR on and press PLAY to view a videotape on the TV.

AV1

POWER

TV	VCR	ACC
		ACTIVE
SWAP	PIP CH	CONTROL FREEZE
DN	UP
SOUND		PICTURE
STATUS/		MENU/
EXIT		SELECT
	MUTE
VOL		CH

	1	2	3
	4	5	6
	7	8	9
	TV/VCR	0
5	A/CH		SURF
	SURF		PIP ON/OFF
	REC •	FORMAT	SLEEP

HELPFUL HINT

To simplify making connections, audio and video cables often have color-code connec- tors. The jacks on your TV are likewise color coded to match the connectors. The coding is as follows:

•Yellow for video (composite)

•Red for the right audio channel

•White for the left audio channel

NOTE: If your VCR is mono (non- stereo), you will connect only one audio cable. You must ensure that the TV is set to MONO for the signal source to which you’ve connected the VCR (INPUT-AV 1, INPUT-AV2, or the side panel inputs [AV3]). Otherwise, you will receive sound from only one of the TV’s speakers. See page 38.

cCHECK IT OUT

You can display the AV1, AV2, or AV3 signal sources in the PIP window. See page 8 of the Quick Use and Setup Guide for information on using the Picture-in-Picture (PIP) feature.

	SAP
AV	DOLBY V PROG.LIST

ITR/	HOME	HOME PERSONAL
RECORD	VIDEO	MOVIES

8