Switching at the exchange | Philips D711, D721 guide

3.3.14Switching at the exchange

You are in the "Brokering" or "Three-party conference" mode and would like to connect both parties to one another without continuing in the con- versation yourself. This function is only available if it has been enabled in the set up menu (see "4.23 Disabling/enabling switching at the exchange). Even after switching, the charges to the parties to whom you have establis- hed the call are debited to your connection.

Prerequisite: this feature must be available on your connection.

Initial state: brokering or three-party conference

Steps:

No.	Description	Input	Display
1	Switch the call
1	Switch the call	so	PLEASE HOOK ON(
			(((((((((((((((
			Å‹Ç¤‰ÏÌÓÛı

Page 39

Image 39

Philips D711, D721 manual Switching at the exchange, Steps Description Input Display Switch the call

Contents

SmartLine D711 Contents Programming SmartLine D721 only Emergency operation switch An emergency Appendix Nection of an analog terminal IntroductionEasy-to-operate high-convenience Isdn telephone General 4713 For the analog port4711 4712 Scope of delivery Call diversion set up Ok keyShift key Change function level Start up Connector for Adapter cable SmartLine D721 only Establishing and undoing a plugged connection Clears the complete line 666 8#± or ‘ Description Input Moving the cursor Dial tone Chaining telephone numbers Direct call Telephoning Further functions If necessary, change s MSN ˜1…8·§ the MSN see With the handsetOn-hook hands Free operation Ber see Use a stored num Number Chain numbersSee Dial telephone Presentation off Steps Description Input Display NumberPresentation on If previously off Telephone number Press funtilDisplayed Confirm selection Edit Memory ±/‘ Key, number is DialledKey, on-hook Steps Description Input Display Ringing tone for Business callOn/off temporarily Business call W, ZNumber also from Displaying the first Most recent entry Call for MSN If necessary, disPlay further entries Nection and accept Steps Description Input Display Place the first conNection on hold End the first con Ringing sounds Required entry Confirm clearing Positive ac Description Input Display Display firstCallback Scroll to Or # Caller identification Steps Description Input Display Lift the handsetActivate malicious Sfpositive ac Is stored Alter the volume Several timesCally and you hear Dial tone Levels Conversation ExchangeEnd the hold state Resume Store the modified Volume can beDtmf digits Keypad signals Altered in nine steps Several times to Store Function during aEdit digits clear Or enter Select the MSN Confirm Description Input Display Park a callEnter the two-digit Code Entering a number To clear the current t 345678 connection, press Placing a callers telephone number in the redial memoryMemory Only during Call Steps Description Input Display Switch the call Mode ProgrammingWhich you wish to Divert calls Diversion is offered Quit display Or o, after Last MSN has Been displayed Input Display Adjust display con If nec. sevTrast in 11 levels Times MSN display for each Lock on or off Steps Description Input Display Switch handsetVolume between Normal and loud Described above Settings as Prefix, national Prefix, international No entry Redial D721Unchangedonly Off Handset volume NormalProgramming 00.00.99/0000 Overview of programmable functions Ror sR S006 On and off S04 Is offered Next call diversion Or the complete Switch overS005 S01 Enter the date and Z TimeIdentification Ring the call charge counter and defining the factor S008Select the required Language S06 S009 Confirm reset S000 S002Prefix code S09 Enter or edit the numberIf nec. Clear digits singly R or sR If nec. Clear digits singly Ror sR S91…8S001 Private or Last digit S004 Enter a blank as a Delimiter between Several schemesDefine ranges by Entering a dash Prefix without S007Enter the local area Code, up to 6 digits S03 Enter the old PINEnter the new PIN Default identification S08Incoming If nec. Clear digits S07Or sR 01901 to Saved S0b Entry Number input, save Saved …9, *, #S9 1…8 Move the cursor Memories Setting can be # switched over be- tween on and offS02 Description Input Display Initiate Emergency operation …2 Not used …6 Not used Analog port SmartLine D721 only Terminal SmartLine D721 On the analog portMSN entry Ringing MSN entry Ringing Tone No. Description Input Pick up ringing or Steps Description Input Initiate consultationDial the internal Users number Second one Put the first connection R Depending on During a conversation 1.1 PicSteps Description Depending on 37# Activating automatic callback on busyHas been activated Otherwise negative #37# 43##43# #61 #21 #67# Old Enter the new New Confirm it byRepeat the new New Confirm it by Check lock #33Description Input Display Select the full lock Code *1# Apply the Isdn Seconds after Lifting the handset #53#Without dialling Destination No. # Check connection Without dialling Input within 73/23/EEC Low-voltage Guideline Appendix When using pulse dialling Key Flash 50 ms … 350 ms Ringing voltage700 Ohm S09 S00 S001 S04 S05 S06 S07 S002 S004 S005 S006 S007 S008 S009 S000 S0b S0w S0r Resetting the unit Reset Programming call pick up D721 only Accepting 53, 70 Conference 29, 38 ConnectingEditing mode Example configuration Number identification Tone ringing Tones Volume Plug-in connection Power failureRedial memory 20, 34, 37 Reset Ringing tone SwitchingPage Page PB Eindhoven Edition 11/99 Postbus

Philips D711, D721 Switching at the exchange, Steps Description Input Display Switch the call

Models: D721 D711

3.3.14Switching at the exchange

Steps:

Description

Input

Display

Switch the call