Emergency operation | Philips D721, D711 specs

5Emergency operation

5.1Emergency operation switch

Emergency operation commences in the event of a power failure. Connected to an NTBA in the emergency mode, the S0 bus can only power a terminal that is capable of emergency operation. If you are operating several terminals on the bus, the emergency mode must only be activated on one of the terminals.

Switching to the emergency mode

Remove all plugs from the terminal.

Take a screw driver and turn the switch to position 1.

Mark this terminal as the emergency terminal

Note:

When delivered, your telephone is not set to emergency operation.

1

2

1

2

Switch setting

1

2

Emergency operation possible

Emergency operation not possible

5.2In an emergency

If the power supply on your NTBA should fail, only the terminal set to the emergency mode will operate on the bus. All calls for the bus will be signalled at this one telephone. When you are making telephone calls, the emergency mode is indicated by a "!" between the date and the time on the display.

SmartLine D721:

The analog port is not available during emergency operation.

67

Image 68

Philips D721, D711 manual Emergency operation

Contents

SmartLine D711 Contents Programming Emergency operation switch An emergency SmartLine D721 only Appendix Introduction Easy-to-operate high-convenienceIsdn telephone Nection of an analog terminal General For the analog port 47114712 4713 Scope of delivery Shift key Change function level Call diversion set upOk key Connector for Adapter cable SmartLine D721 only Start up Establishing and undoing a plugged connection 666 8# ± or ‘Description Input Moving the cursor Clears the complete line Dial tone Telephoning Chaining telephone numbers Direct call Further functions With the handset On-hook handsFree operation If necessary, change s MSN ˜1…8·§ the MSN see Use a stored num Ber see Chain numbers SeeDial telephone Number Steps Description Input Display Number Presentation onIf previously off Presentation off Press funtil Displayed Confirm selectionEdit Telephone number ±/‘ Memory Key, on-hook Key, number isDialled Steps Description Input Display On/off temporarily Ringing tone forBusiness call Number also from Business callW, Z Play further entries Displaying the first Most recent entry Call for MSNIf necessary, dis Steps Description Input Display Place the first con Nection on holdEnd the first con Nection and accept Ringing sounds Description Input Display Display first CallbackScroll to Or # Required entry Confirm clearing Positive ac Activate malicious Sfpositive ac Caller identificationSteps Description Input Display Lift the handset Alter the volume Several times Cally and you hear Dial toneLevels Is stored Exchange End the hold stateResume Conversation Volume can be Dtmf digits Keypad signalsAltered in nine steps Several times to Store the modified Function during a Edit digits clear Or enterSelect the MSN Store Description Input Display Park a call Enter the two-digitCode Confirm Entering a number Memory Only during Call To clear the current t 345678 connection, pressPlacing a callers telephone number in the redial memory Steps Description Input Display Switch the call Programming Which you wish toDivert calls Mode Diversion is offered Input Display Adjust display con If nec. sev Trast in 11 levels TimesMSN display for each Quit display Or o, after Last MSN has Been displayed Steps Description Input Display Switch handset Volume betweenNormal and loud Lock on or off Settings as Described above D721Unchangedonly Off Handset volume Normal Programming00.00.99/0000 Prefix, national Prefix, international No entry Redial Overview of programmable functions S006 Ror sR S04 On and off Next call diversion Is offered Switch over S005S01 Or the complete Identification Enter the date and ZTime S008 Select the requiredLanguage Ring the call charge counter and defining the factor S06 Confirm reset S009 Prefix code S000S002 If nec. Clear digits singly R or sR S09Enter or edit the number S91…8 S001Private or If nec. Clear digits singly Ror sR Last digit Define ranges by Entering a dash S004Enter a blank as a Delimiter between Several schemes S007 Enter the local areaCode, up to 6 digits Prefix without Enter the new PIN S03Enter the old PIN Incoming Default identificationS08 S07 Or sR01901 to If nec. Clear digits S0b Saved Number input, save Entry …9, *, # S9 1…8Move the cursor Saved Setting can be # switched over be- tween on and off S02Description Input Display Initiate Memories Emergency operation Analog port SmartLine D721 only …2 Not used …6 Not used SmartLine D721 On the analog port MSN entry RingingMSN entry Ringing Tone Terminal Steps Description Input Initiate consultation Dial the internalUsers number No. Description Input Pick up ringing or During a conversation 1.1 Pic Steps DescriptionDepending on Second one Put the first connection R Depending on Has been activated Otherwise negative 37#Activating automatic callback on busy #43# #37#43# #21 #61 Repeat the new New Confirm it by #67#Old Enter the new New Confirm it by #33 Description Input Display Select the full lockCode *1# Apply the Isdn Check lock #53# Without dialling Destination No. # Check connectionWithout dialling Input within Seconds after Lifting the handset Appendix 73/23/EEC Low-voltage Guideline 700 Ohm When using pulse diallingKey Flash 50 ms … 350 ms Ringing voltage S04 S05 S06 S07 S09 S00 S001 Resetting the unit Reset Programming call pick up D721 only S002 S004 S005 S006 S007 S008 S009 S000 S0b S0w S0r Conference 29, 38 Connecting Editing modeExample configuration Number identification Accepting 53, 70 Plug-in connection Power failure Redial memory 20, 34, 37 ResetRinging tone Switching Tone ringing Tones VolumePage Page Postbus PB Eindhoven Edition 11/99