Programming, Which you wish to, Divert calls, Mode | Philips D721

• B (on busy):

• N (no reply):

3.4Further functions

3.4.1Modifying or switching call diversion on/off

An arriving call can be diverted to a different, previously defined connection, e.g. if you have temporarily moved to its location and you are expecting an important call. You can set up separate call diversion for each MSN in one of the following modes:

•U (unconditional): always - call diversion immediately becomes active when a call arrives

call diversion is only active when your connection is busy

after a time - call diversion is only activated after about 15 seconds

Initial state: idle

Steps:

	No.		Description		Input		Display
1		Initiate
1		Initiate		r			MSN8˜1…8·:§
		programming
							Å‹Ç¤‰ÏÌÓÛı


	2		Select the MSN for		¡…{		MSN1U:PRIVATE
			which you wish to				§NUMBER?
			which you wish to
			divert calls.				Å‹Ç¤‰ÏÌÓÛı





	3	If required:			r		MSN1B:PRIVATE
		define the diversion					§NUMBER?
		mode:					Å‹Ç¤‰ÏÌÓÛı

•U = unconditional

•B = on busy

•N = no reply (see also 4.6)

4	If required:	s}ç	MSN2B:BUSINESS
	Change the MSN		§NUMBER?

Å‹Ç¤‰ÏÌÓÛı

5Enter, modify or clear the diversion destination

Z

RZ sR

MSN2B:BUSINESS 987654§

Å‹Ç¤‰ÏÌÓÛı

39

Image 40

Philips D721, D711 manual Programming, Which you wish to, Divert calls, Mode, = unconditional = on busy = no reply see also

Contents

SmartLine D711 Contents Programming Emergency operation switch An emergency SmartLine D721 only Appendix Introduction Easy-to-operate high-convenienceIsdn telephone Nection of an analog terminal General For the analog port 47114712 4713 Scope of delivery Ok key Call diversion set upShift key Change function level Connector for Adapter cable SmartLine D721 only Start up Establishing and undoing a plugged connection 666 8# ± or ‘Description Input Moving the cursor Clears the complete line Dial tone Telephoning Chaining telephone numbers Direct call Further functions With the handset On-hook handsFree operation If necessary, change s MSN ˜1…8·§ the MSN see Use a stored num Ber see Chain numbers SeeDial telephone Number Steps Description Input Display Number Presentation onIf previously off Presentation off Press funtil Displayed Confirm selectionEdit Telephone number ±/‘ Memory Dialled Key, number isKey, on-hook Steps Description Input Display Business call Ringing tone forOn/off temporarily W, Z Business callNumber also from If necessary, dis Displaying the first Most recent entry Call for MSNPlay further entries Steps Description Input Display Place the first con Nection on holdEnd the first con Nection and accept Ringing sounds Description Input Display Display first CallbackScroll to Or # Required entry Confirm clearing Positive ac Steps Description Input Display Lift the handset Caller identificationActivate malicious Sfpositive ac Alter the volume Several times Cally and you hear Dial toneLevels Is stored Exchange End the hold stateResume Conversation Volume can be Dtmf digits Keypad signalsAltered in nine steps Several times to Store the modified Function during a Edit digits clear Or enterSelect the MSN Store Description Input Display Park a call Enter the two-digitCode Confirm Entering a number Placing a callers telephone number in the redial memory To clear the current t 345678 connection, pressMemory Only during Call Steps Description Input Display Switch the call Programming Which you wish toDivert calls Mode Diversion is offered Input Display Adjust display con If nec. sev Trast in 11 levels TimesMSN display for each Quit display Or o, after Last MSN has Been displayed Steps Description Input Display Switch handset Volume betweenNormal and loud Lock on or off Settings as Described above D721Unchangedonly Off Handset volume Normal Programming00.00.99/0000 Prefix, national Prefix, international No entry Redial Overview of programmable functions S006 Ror sR S04 On and off Next call diversion Is offered Switch over S005S01 Or the complete Time Enter the date and ZIdentification S008 Select the requiredLanguage Ring the call charge counter and defining the factor S06 Confirm reset S009 S002 S000Prefix code Enter or edit the number S09If nec. Clear digits singly R or sR S91…8 S001Private or If nec. Clear digits singly Ror sR Last digit Enter a blank as a Delimiter between Several schemes S004Define ranges by Entering a dash S007 Enter the local areaCode, up to 6 digits Prefix without Enter the old PIN S03Enter the new PIN S08 Default identificationIncoming S07 Or sR01901 to If nec. Clear digits S0b Saved Number input, save Entry …9, *, # S9 1…8Move the cursor Saved Setting can be # switched over be- tween on and off S02Description Input Display Initiate Memories Emergency operation Analog port SmartLine D721 only …2 Not used …6 Not used SmartLine D721 On the analog port MSN entry RingingMSN entry Ringing Tone Terminal Steps Description Input Initiate consultation Dial the internalUsers number No. Description Input Pick up ringing or During a conversation 1.1 Pic Steps DescriptionDepending on Second one Put the first connection R Depending on Activating automatic callback on busy 37#Has been activated Otherwise negative 43# #37##43# #21 #61 Old Enter the new New Confirm it by #67#Repeat the new New Confirm it by #33 Description Input Display Select the full lockCode *1# Apply the Isdn Check lock #53# Without dialling Destination No. # Check connectionWithout dialling Input within Seconds after Lifting the handset Appendix 73/23/EEC Low-voltage Guideline Key Flash 50 ms … 350 ms Ringing voltage When using pulse dialling700 Ohm S04 S05 S06 S07 S09 S00 S001 Resetting the unit Reset Programming call pick up D721 only S002 S004 S005 S006 S007 S008 S009 S000 S0b S0w S0r Conference 29, 38 Connecting Editing modeExample configuration Number identification Accepting 53, 70 Plug-in connection Power failure Redial memory 20, 34, 37 ResetRinging tone Switching Tone ringing Tones VolumePage Page Postbus PB Eindhoven Edition 11/99