Philips DMP-BD30 operating instructions TV screen and video, Hdmi connections

	TV screen and video		Page
	The images from this unit do	≥Make sure that the television is connected to the VIDEO OUT terminal, S VIDEO OUT	6, 7
	not appear on the television.	terminal, COMPONENT VIDEO OUT terminals or HDMI AV OUT terminal on this unit.	—
		≥Make sure that the television’s input setting (e.g., AV 1) is correct.
	Picture is distorted.	≥An incorrect resolution is selected in “Component Resolution”, when the television is connected to	24
		COMPONENT VIDEO OUT terminals. While stopped, press and hold [∫] and [1] (PLAY) on the main
		unit at the same time for more than 5 seconds to cancel this setting. Set the item again.	24
		≥If “BD-Video 24p Output” is turned “On” when the unit is connected to a TV through any
		terminal other than HDMI, images may not display properly. In this case, turn “BD-Video 24p
		Output” to “Off”.	—
		≥The unit and television are using different video systems. While stopped, keep pressing [∫]
		and [< OPEN/CLOSE] on the main unit for 5 or more seconds. The system switches from
		PAL to NTSC or vice versa.
		≥The system used on the disc doesn’t match your television.	—
		– PAL discs cannot be correctly viewed on an NTSC television.
		– This unit can convert NTSC signals to PAL60 for viewing on a PAL television (“NTSC	22
		Contents Output” in the “Picture”).	—
		≥[DivX] Images may not be output due to how files were created.
	Picture stops.	≥[DivX] Picture may stop if the DivX files are greater than 2 GB.	—
	The screen changes	≥When the “Screen Saver Function” in the Setup menu is set to “On”, the display may return to	24
	automatically.	the screen saver mode automatically if there is no operation for 10 minutes or more.
	Video is not output in high	≥High definition video cannot be output through the VIDEO OUT or S VIDEO OUT terminals.	—
	definition.	≥Confirm that the “HDMI Video Mode”, “HDMI Video Format”, and “Component Resolution” in	24
		the Setup menu are set properly.
		≥The video output resolution is restricted to “576p/480p” when DVD-Video, DivX and	—
		BD-Video discs recorded at a rate of 50 frames per second is output from the COMPONENT
		VIDEO OUT terminals.
	Status messages do not appear.	≥Select “Automatic” in “On-screen Messages” in the Setup menu.	24
	The 4:3 aspect ratio picture	≥Use the television to change the aspect. Refer to your television’s operating instructions.	—
	expands left and right.	≥When using a component video cable, set “Progressive” to “Off”. If the situation is not	21, 24
	Screen size is wrong.	restored after that, set “TV Aspect” to “4:3 Pan & Scan”.
	There is a lot of after-image	≥Turn “3D NR” or “Integrated NR” off if it is on.	21
	when playing video.
	When playing DVD-Video using	≥Set “Progressive” of “Picture” menu on the on-screen menu to “Off”. This problem is caused	21
	progressive output, one part of	by the editing method or material used on DVD-Video, but should be corrected if you use
	the picture momentarily	interlace output.
	appears to be doubled up.	≥When the unit is connected using HDMI terminal, refer to “HDMI connections” (> below).	—
	There is no apparent change in	≥The effect is less perceivable with some types of video.	—
	picture quality when adjusted
	with the “Picture” menu in the
	on-screen menu.
	The masked-off area is masked	≥If the “Screen Saver Function” in the Setup menu is set to “Off”, the masked-off area is	24
	in gray.	displayed in black.
	Sound
	No sound.	≥Check the connections and the “Digital Audio Output” settings. Check the input mode on the	6–8, 23
	Low volume.	amplifier/receiver if you have connected one.	12
	Distorted sound.	≥Press [AUDIO] to select the audio.
	Cannot hear the desired audio	≥Turn off “V. Surround” in the following cases.	21
	type.	– When using discs that do not have surround sound effects such as Karaoke discs.
		– When playing bilingual broadcast programmes.	24
		≥Match the speaker settings with the connected equipment. Change multi channel speaker
		settings by selecting “Multi-Channel” in “Speaker”.	—
		≥The sound effects (Re-master, V. Surround, etc.) will not work when the bitstream signal is
		output from the HDMI AV OUT terminal or the DIGITAL AUDIO OUT terminal.	—
		≥When “BD-Video Secondary Audio” is set to “Off”, Dolby Digital Plus, Dolby TrueHD and
		DTS-HD are output from the DIGITAL AUDIO OUT terminal as Dolby Digital or DTS Digital
		Surround bitstream.	—
		≥[DivX] Audio may not be output due to how files were created.
	Cannot switch audio.	≥There are discs for which audio cannot be changed because of how the disc was created.	—
		≥When connecting an amplifier/receiver using a coaxial cable, optical digital audio cable or an	7, 8, 23
		HDMI cable, you cannot switch the audio if “Digital Audio Output” is set to “Bitstream”. Set
		“Digital Audio Output” to “PCM” or connect using audio cables.
	HDMI connections
	The images from this unit do	≥Press [∫] and [1] (PLAY) simultaneously on the unit for more than 5 seconds to shift the	22
	not appear on the television.	mode to one more compatible with HDMI equipment. However, Dolby Digital Plus, Dolby
		TrueHD, and DTS-HD audio are not output in bitstream. To output the bitstream, select
	Picture is distorted.	“Default Settings” to restore the factory presets and make proper settings.	24
		≥To output video from a device connected with an HDMI cable, set “HDMI Video Mode” to “On”
		in the Setup menu.	—
		≥Picture may not be seen when more than 4 devices are connected with HDMI cables.
		Reduce the number of connected devices.	24
		≥When “BD-Video 24p Output” is set to “On”, HDMI authentication takes place where 24p
		images switch to other images, and a black screen is displayed.
	The 4:3 aspect ratio picture	≥Change “TV Aspect” type to “16:9”.	24
	expands left and right.
	Screen size is wrong.
RQT9038		(Continued on the next page)

28