PS2MS Wakeup from S3/S4/S5, USB Resume | Philips EPIA-MII instruction

BIOS Setup

PS2MS Wakeup from S3/S4/S5

This setting can be used to wakeup the system from power saving mode through mouse. Settings: Disabled and Enabled

PS2KB Wakeup from S3/S4/S5

Select which Hot-Key to wake-up the system from power saving mode.

Settings: Disabled, Ctrl+F1, Ctrl+F2, Ctrl+F3, Ctrl+F4, Ctrl+F5, Ctrl+F6, Ctrl+F7, Ctrl+F8, Ctrl+F9, Ctrl+F10, Ctrl+F11, Ctrl+F12, Power, Wake and Any Key

USB Resume

Decide whether or not USB devices can wake the system from suspend state. Settings: Disabled and Enabled

PowerOn by PCI Card

Decide whether or not any PCI card can power up the system or resume from suspend state. Such PCI cards include LAN, onboard USB ports, etc. Settings: Disabled and Enabled

Wake On LAN/Ring Connector

Decide whether or not any Ring-In signals from the modem can wake up the system or resume from suspend state. Settings: Disabled and Enabled

RTC Alarm Resume

The field is used to enable or disable the feature of booting up the system on a scheduled time/date. Settings: Disabled and Enabled

Date (of Month)

This field can only be set if RTC Alarm Resume is enabled. The field specifies the date for RTC Alarm Resume.

Resume Time (hh:mm:ss)

This field can only be set if RTC Alarm Resume is enabled. The field specifies the time for RTC Alarm Resume.

3-21

Image 56

Philips EPIA-MII PS2MS Wakeup from S3/S4/S5, PS2KB Wakeup from S3/S4/S5, USB Resume, PowerOn by PCI Card, RTC Alarm Resume

Contents

User’s Manual Disclaimer CopyrightTrademarks FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Form Factor Onboard I/O ConnectorsBack Panel I/O Ports Mainboard Layout Back Panel Placement of Add-On Module Add-On Module Back Panel Ports Slots Onboard Connectors and Jumpers Connecter/Jumper Description Chapter Installation CPU VIA C3TM E-Series Processor VIA Eden Processor Memory Module Installation DDR Sdram Module Installation Procedures Available DDR Sdram Configurations Connecting the Power Supply ATX 20-Pin Power Connector Mouse Port PS2MS Keyboard Port PS2KB VGA Out USB PortsRJ45 10/100 NIC Port Video Port Card Slots PCMCIA, CF Ieee 1394 PortSerial Port COM1 Audio Jacks Line-In, Line-Out, Microphone Connectors Hard Disk Connectors IDE1 & IDE2IDE1 Primary IDE Connector IDE2 Secondary IDE Connector Speaker Case Connector FpanelPower LED PWR LED IrDA Infrared Module Connector FIR Consumer Infrared Module / PS2 Header Kbms USB pin-header USB3/4 Wake-on LAN WOL Floppy Disk Drive Connector FDD COM2 The Second Serial Port CD Audio Connector Cdin Front Audio Panel Faudio SMBus Connector SMBus LPT Pin Header LPT Port Connector Lvds Connector Optional RCA Video or S/PDIF Select Spdifsel JumpersClear Cmos Clearcmos Peripheral Component Interconnect PCI PCI Interrupt Request Routing Bios Setup Entering Setup Control Keys Getting Help Main MenuSub-Menu General Help F1 Main Menu Load Fail-Safe Defaults Load Optimized DefaultsSet Supervisor Password Set User Password Standard Cmos Features DateTime Drive A/B IDE Primary Master/Slave, Secondary Master/Slave Advanced Bios Features Quick Power On Self TestVirus Warning CPU L2 Cache ECC Checking First/Second/Third Boot Device Boot Other DeviceBoot Up Floppy Seek Swap Floppy Drive Boot Up NumLock Status Typematic Rate SettingTypematic Delay Msec Typematic Rate Chars/Sec Show Summary Information Display Small Logo AGP Aperture Size Advanced Chipset FeaturesAGP Mode Internal CPU Direct Access FB AGP Fast WriteCPU to PCI Post Write Select Display Device IDE Prefetch Mode Integrated PeripheralsOnboard IDE Channel 1/2 Display Card Priority Onboard Lan Boot ROM AC97 AudioVIA OnChip LAN OnChip USB Controller Parallel Port Mode SuperIO DeviceOnboard FDC Controller Onboard Serial Port 1/2 EPP Mode Select ECP Mode Use DMAOnboard Fast IR Fast IR IRQ Acpi Suspend Type Power Management SetupHDD Power Down Power Management Timer Power Off by PwrbtnRun Vgabios if S3 Resume Video Off Option Peripheral Activities PowerOn by PCI Card Wake On LAN/Ring ConnectorRTC Alarm Resume PS2MS Wakeup from S3/S4/S5 IRQs Activities Primary Intr PNP/PCI Configurations PNP OS InstalledReset Configuration Data Resource Controlled By Assign IRQ For VGA/USB IRQ Resources PC Health Status Frequency / Voltage Control Dram ClockDram Timing Dram CAS Latency Dram Command Rate Bank InterleavePrecharge to Active Trp Active to Precharge Tras Spread Spectrum Dram VoltageCPU Clock Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Running the Driver Utilities CD Driver UtilitiesGetting Started CD Content Chapter