Load Optimized Defaults | Philips EPIA-MII instruction

BIOS Setup

Load Optimized Defaults

This option on the main menu allows users to restore all the BIOS settings to the default Optimized values. The Optimized Defaults are the default values also set by the mainboard manufacturer for both optimized and stable performance of the mainboard.

When you select Load Optimized Defaults, a message as below appears:

Entering Y loads the default values that are factory settings for optimal and stable system performance.

3-31

Image 66

Philips EPIA-MII user manual Load Optimized Defaults

Contents

User’s Manual Copyright TrademarksDisclaimer FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Onboard I/O Connectors Back Panel I/O PortsForm Factor Mainboard Layout Back Panel Placement of Add-On Module Add-On Module Back Panel Ports Slots Onboard Connectors and Jumpers Connecter/Jumper Description Chapter Installation CPU VIA C3TM E-Series Processor VIA Eden Processor Memory Module Installation DDR Sdram Module Installation Procedures Available DDR Sdram Configurations Connecting the Power Supply ATX 20-Pin Power Connector Mouse Port PS2MS Keyboard Port PS2KB RJ45 10/100 NIC Port VGA OutUSB Ports Video Port Ieee 1394 Port Serial Port COM1Card Slots PCMCIA, CF Audio Jacks Line-In, Line-Out, Microphone IDE1 Primary IDE Connector ConnectorsHard Disk Connectors IDE1 & IDE2 IDE2 Secondary IDE Connector Case Connector Fpanel Power LED PWR LEDSpeaker IrDA Infrared Module Connector FIR Consumer Infrared Module / PS2 Header Kbms USB pin-header USB3/4 Wake-on LAN WOL Floppy Disk Drive Connector FDD COM2 The Second Serial Port CD Audio Connector Cdin Front Audio Panel Faudio SMBus Connector SMBus LPT Pin Header LPT Port Connector Lvds Connector Optional Jumpers Clear Cmos ClearcmosRCA Video or S/PDIF Select Spdifsel Peripheral Component Interconnect PCI PCI Interrupt Request Routing Bios Setup Entering Setup Control Keys Sub-Menu Getting HelpMain Menu General Help F1 Main Menu Set Supervisor Password Load Fail-Safe DefaultsLoad Optimized Defaults Set User Password Time Standard Cmos FeaturesDate Drive A/B IDE Primary Master/Slave, Secondary Master/Slave Virus Warning Advanced Bios FeaturesQuick Power On Self Test CPU L2 Cache ECC Checking Boot Up Floppy Seek First/Second/Third Boot DeviceBoot Other Device Swap Floppy Drive Typematic Delay Msec Boot Up NumLock StatusTypematic Rate Setting Typematic Rate Chars/Sec Show Summary Information Display Small Logo Advanced Chipset Features AGP Mode InternalAGP Aperture Size CPU to PCI Post Write CPU Direct Access FBAGP Fast Write Select Display Device Onboard IDE Channel 1/2 IDE Prefetch ModeIntegrated Peripherals Display Card Priority VIA OnChip LAN Onboard Lan Boot ROMAC97 Audio OnChip USB Controller Onboard FDC Controller Parallel Port ModeSuperIO Device Onboard Serial Port 1/2 Onboard Fast IR EPP Mode SelectECP Mode Use DMA Fast IR IRQ Power Management Setup HDD Power DownAcpi Suspend Type Run Vgabios if S3 Resume Power Management TimerPower Off by Pwrbtn Video Off Option Peripheral Activities RTC Alarm Resume PowerOn by PCI CardWake On LAN/Ring Connector PS2MS Wakeup from S3/S4/S5 IRQs Activities Primary Intr Reset Configuration Data PNP/PCI ConfigurationsPNP OS Installed Resource Controlled By Assign IRQ For VGA/USB IRQ Resources PC Health Status Dram Timing Frequency / Voltage ControlDram Clock Dram CAS Latency Precharge to Active Trp Dram Command RateBank Interleave Active to Precharge Tras Dram Voltage CPU ClockSpread Spectrum Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Driver Utilities Getting StartedRunning the Driver Utilities CD CD Content Chapter