SuperIO Device, Onboard FDC Controller | Philips EPIA-MII instruction

Chapter 3

SuperIO Device

Press Enter to enter the sub-menu and the following screen appears:

Onboard FDC Controller

Enable the onboard floppy controller. Select Enabled when you have installed a floppy disk drive. Settings: Enabled, Disabled

Onboard Serial Port 1/2

Set the base I/O port address and IRQ for the onboard serial port A/serial port B. Selecting Auto allows BIOS to automatically determine the correct base I/O port address. Settings:

Port	Settings
1	Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Auto

2Disabled 3F8/IRQ4 2F8/IRQ3 3E8/IRQ4 2E8/IRQ3 Auto

Onboard Parallel Port

This specifies the I/O port address and IRQ of the onboard parallel port.

Settings: Disabled, 378/IRQ7, 278/IRQ5, 3BC/IRQ7

Parallel Port Mode

Set the parallel port mode. To operate the onboard parallel port as Standard Parallel Port, choose SPP. To operate the onboard parallel port in the EPP mode, choose EPP. By choosing ECP, the onboard parallel port will operate in ECP mode. Choosing ECP + EPP will allow the onboard parallel port to support both the ECP and EPP modes simultaneously.

Settings: SPP, EPP, ECP, ECP + EPP

3-16

Image 51

Philips EPIA-MII user manual SuperIO Device, Onboard FDC Controller, Onboard Serial Port 1/2, Onboard Parallel Port

Contents

User’s Manual Copyright TrademarksDisclaimer FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Onboard I/O Connectors Back Panel I/O PortsForm Factor Back Panel Mainboard Layout Add-On Module Placement of Add-On Module Slots Back Panel Ports Connecter/Jumper Description Onboard Connectors and Jumpers Chapter Installation VIA C3TM E-Series Processor CPU VIA Eden Processor DDR Sdram Module Installation Procedures Memory Module Installation Available DDR Sdram Configurations ATX 20-Pin Power Connector Connecting the Power Supply Keyboard Port PS2KB Mouse Port PS2MS Video Port VGA OutUSB Ports RJ45 10/100 NIC Port Ieee 1394 Port Serial Port COM1Card Slots PCMCIA, CF Audio Jacks Line-In, Line-Out, Microphone IDE2 Secondary IDE Connector ConnectorsHard Disk Connectors IDE1 & IDE2 IDE1 Primary IDE Connector Case Connector Fpanel Power LED PWR LEDSpeaker Consumer Infrared Module / PS2 Header Kbms IrDA Infrared Module Connector FIR Wake-on LAN WOL USB pin-header USB3/4 COM2 The Second Serial Port Floppy Disk Drive Connector FDD Front Audio Panel Faudio CD Audio Connector Cdin LPT Pin Header LPT SMBus Connector SMBus Lvds Connector Optional Port Connector Jumpers Clear Cmos ClearcmosRCA Video or S/PDIF Select Spdifsel PCI Interrupt Request Routing Peripheral Component Interconnect PCI Bios Setup Control Keys Entering Setup General Help F1 Getting HelpMain Menu Sub-Menu Main Menu Set User Password Load Fail-Safe DefaultsLoad Optimized Defaults Set Supervisor Password Drive A/B Standard Cmos FeaturesDate Time IDE Primary Master/Slave, Secondary Master/Slave CPU L2 Cache ECC Checking Advanced Bios FeaturesQuick Power On Self Test Virus Warning Swap Floppy Drive First/Second/Third Boot DeviceBoot Other Device Boot Up Floppy Seek Typematic Rate Chars/Sec Boot Up NumLock StatusTypematic Rate Setting Typematic Delay Msec Display Small Logo Show Summary Information Advanced Chipset Features AGP Mode InternalAGP Aperture Size Select Display Device CPU Direct Access FBAGP Fast Write CPU to PCI Post Write Display Card Priority IDE Prefetch ModeIntegrated Peripherals Onboard IDE Channel 1/2 OnChip USB Controller Onboard Lan Boot ROMAC97 Audio VIA OnChip LAN Onboard Serial Port 1/2 Parallel Port ModeSuperIO Device Onboard FDC Controller Fast IR IRQ EPP Mode SelectECP Mode Use DMA Onboard Fast IR Power Management Setup HDD Power DownAcpi Suspend Type Video Off Option Power Management TimerPower Off by Pwrbtn Run Vgabios if S3 Resume Peripheral Activities PS2MS Wakeup from S3/S4/S5 PowerOn by PCI CardWake On LAN/Ring Connector RTC Alarm Resume Primary Intr IRQs Activities Resource Controlled By PNP/PCI ConfigurationsPNP OS Installed Reset Configuration Data Assign IRQ For VGA/USB IRQ Resources PC Health Status Dram CAS Latency Frequency / Voltage ControlDram Clock Dram Timing Active to Precharge Tras Dram Command RateBank Interleave Precharge to Active Trp Dram Voltage CPU ClockSpread Spectrum Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Driver Utilities Getting StartedRunning the Driver Utilities CD CD Content Chapter