Mainboard Specifications | Philips EPIA-MII guide

Chapter 1

Mainboard Specifications

CPU

•VIA C3 / EDEN EBGA Processor (onboard)

•Enhanced Ball Grid Array Package (EBGA)

•Internal L1 128KB and L2 64KB cache memory

Chipset

•VIA CLE266 North Bridge

•VT8235 South Bridge

Memory

• 1 x DDR266 DIMM socket (up to 1 GB)

Expansion Slots

• 1 x PCI

Graphics

• Integrated VIA Castlerock AGP graphics

Audio

• VT1616, six-channel AC’97 Codec

Onboard IEEE 1394 (optional)

• VIA VT6307S IEEE 1394

LAN

• VIA VT6103 10/100 Base-T Ethernet PHY

IDE

• 2 X UltraDMA 66/100/133 Connectors

OnModule CardBus/CF

• RICOH 476II

LVDS (optional)

VIA VT1631 LVDS Transmitter

1-2

Image 9

Philips EPIA-MII user manual Mainboard Specifications

Contents

User’s Manual Copyright TrademarksDisclaimer FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Onboard I/O Connectors Back Panel I/O PortsForm Factor Back Panel Mainboard Layout Add-On Module Placement of Add-On Module Slots Back Panel Ports Connecter/Jumper Description Onboard Connectors and Jumpers Chapter Installation VIA C3TM E-Series Processor CPU VIA Eden Processor DDR Sdram Module Installation Procedures Memory Module Installation Available DDR Sdram Configurations ATX 20-Pin Power Connector Connecting the Power Supply Keyboard Port PS2KB Mouse Port PS2MS USB Ports VGA OutRJ45 10/100 NIC Port Video Port Ieee 1394 Port Serial Port COM1Card Slots PCMCIA, CF Audio Jacks Line-In, Line-Out, Microphone Hard Disk Connectors IDE1 & IDE2 ConnectorsIDE1 Primary IDE Connector IDE2 Secondary IDE Connector Case Connector Fpanel Power LED PWR LEDSpeaker Consumer Infrared Module / PS2 Header Kbms IrDA Infrared Module Connector FIR Wake-on LAN WOL USB pin-header USB3/4 COM2 The Second Serial Port Floppy Disk Drive Connector FDD Front Audio Panel Faudio CD Audio Connector Cdin LPT Pin Header LPT SMBus Connector SMBus Lvds Connector Optional Port Connector Jumpers Clear Cmos ClearcmosRCA Video or S/PDIF Select Spdifsel PCI Interrupt Request Routing Peripheral Component Interconnect PCI Bios Setup Control Keys Entering Setup Main Menu Getting HelpSub-Menu General Help F1 Main Menu Load Optimized Defaults Load Fail-Safe DefaultsSet Supervisor Password Set User Password Date Standard Cmos FeaturesTime Drive A/B IDE Primary Master/Slave, Secondary Master/Slave Quick Power On Self Test Advanced Bios FeaturesVirus Warning CPU L2 Cache ECC Checking Boot Other Device First/Second/Third Boot DeviceBoot Up Floppy Seek Swap Floppy Drive Typematic Rate Setting Boot Up NumLock StatusTypematic Delay Msec Typematic Rate Chars/Sec Display Small Logo Show Summary Information Advanced Chipset Features AGP Mode InternalAGP Aperture Size AGP Fast Write CPU Direct Access FBCPU to PCI Post Write Select Display Device Integrated Peripherals IDE Prefetch ModeOnboard IDE Channel 1/2 Display Card Priority AC97 Audio Onboard Lan Boot ROMVIA OnChip LAN OnChip USB Controller SuperIO Device Parallel Port ModeOnboard FDC Controller Onboard Serial Port 1/2 ECP Mode Use DMA EPP Mode SelectOnboard Fast IR Fast IR IRQ Power Management Setup HDD Power DownAcpi Suspend Type Power Off by Pwrbtn Power Management TimerRun Vgabios if S3 Resume Video Off Option Peripheral Activities Wake On LAN/Ring Connector PowerOn by PCI CardRTC Alarm Resume PS2MS Wakeup from S3/S4/S5 Primary Intr IRQs Activities PNP OS Installed PNP/PCI ConfigurationsReset Configuration Data Resource Controlled By Assign IRQ For VGA/USB IRQ Resources PC Health Status Dram Clock Frequency / Voltage ControlDram Timing Dram CAS Latency Bank Interleave Dram Command RatePrecharge to Active Trp Active to Precharge Tras Dram Voltage CPU ClockSpread Spectrum Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Driver Utilities Getting StartedRunning the Driver Utilities CD CD Content Chapter