PNP/PCI Configurations, PNP OS Installed | Philips EPIA-MII specs

BIOS Setup

PNP/PCI Configurations

This section describes the BIOS configuration of the PCI bus system. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.

PNP OS Installed

When set to Yes, BIOS will only initialize the PnP cards used for booting (VGA, IDE, SCSI). The rest of the cards will be initialized by the PnP operating system like Windows® 95 or 98/98SE. When set to No, BIOS will initialize all the PnP cards. Set to Yes the operating system is Plug & Play capable. Settings: No and Yes

Reset Configuration Data

Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system can not boot. Settings: Enabled and

Disabled

Resource Controlled By

The BIOS can automatically configure all the boot and Plug and Play compatible devices. Choose Auto(ESCD) if unsure, the BIOS will automatically assign IRQ, DMA and memory base address fields. Settings:

Auto (ESCD) and Manual

3-23

Image 58

Philips EPIA-MII user manual PNP/PCI Configurations, PNP OS Installed, Reset Configuration Data, Resource Controlled By

Contents

User’s Manual Trademarks CopyrightDisclaimer FCC-B Radio Frequency Interference Statement Safety Instructions Box Contents Page Table of Contents Chapter Mainboard Specifications Back Panel I/O Ports Onboard I/O ConnectorsForm Factor Mainboard Layout Back Panel Placement of Add-On Module Add-On Module Back Panel Ports Slots Onboard Connectors and Jumpers Connecter/Jumper Description Chapter Installation CPU VIA C3TM E-Series Processor VIA Eden Processor Memory Module Installation DDR Sdram Module Installation Procedures Available DDR Sdram Configurations Connecting the Power Supply ATX 20-Pin Power Connector Mouse Port PS2MS Keyboard Port PS2KB RJ45 10/100 NIC Port VGA OutUSB Ports Video Port Serial Port COM1 Ieee 1394 PortCard Slots PCMCIA, CF Audio Jacks Line-In, Line-Out, Microphone IDE1 Primary IDE Connector ConnectorsHard Disk Connectors IDE1 & IDE2 IDE2 Secondary IDE Connector Power LED PWR LED Case Connector FpanelSpeaker IrDA Infrared Module Connector FIR Consumer Infrared Module / PS2 Header Kbms USB pin-header USB3/4 Wake-on LAN WOL Floppy Disk Drive Connector FDD COM2 The Second Serial Port CD Audio Connector Cdin Front Audio Panel Faudio SMBus Connector SMBus LPT Pin Header LPT Port Connector Lvds Connector Optional Clear Cmos Clearcmos JumpersRCA Video or S/PDIF Select Spdifsel Peripheral Component Interconnect PCI PCI Interrupt Request Routing Bios Setup Entering Setup Control Keys Sub-Menu Getting HelpMain Menu General Help F1 Main Menu Set Supervisor Password Load Fail-Safe DefaultsLoad Optimized Defaults Set User Password Time Standard Cmos FeaturesDate Drive A/B IDE Primary Master/Slave, Secondary Master/Slave Virus Warning Advanced Bios FeaturesQuick Power On Self Test CPU L2 Cache ECC Checking Boot Up Floppy Seek First/Second/Third Boot DeviceBoot Other Device Swap Floppy Drive Typematic Delay Msec Boot Up NumLock StatusTypematic Rate Setting Typematic Rate Chars/Sec Show Summary Information Display Small Logo AGP Mode Internal Advanced Chipset FeaturesAGP Aperture Size CPU to PCI Post Write CPU Direct Access FBAGP Fast Write Select Display Device Onboard IDE Channel 1/2 IDE Prefetch ModeIntegrated Peripherals Display Card Priority VIA OnChip LAN Onboard Lan Boot ROMAC97 Audio OnChip USB Controller Onboard FDC Controller Parallel Port ModeSuperIO Device Onboard Serial Port 1/2 Onboard Fast IR EPP Mode SelectECP Mode Use DMA Fast IR IRQ HDD Power Down Power Management SetupAcpi Suspend Type Run Vgabios if S3 Resume Power Management TimerPower Off by Pwrbtn Video Off Option Peripheral Activities RTC Alarm Resume PowerOn by PCI CardWake On LAN/Ring Connector PS2MS Wakeup from S3/S4/S5 IRQs Activities Primary Intr Reset Configuration Data PNP/PCI ConfigurationsPNP OS Installed Resource Controlled By Assign IRQ For VGA/USB IRQ Resources PC Health Status Dram Timing Frequency / Voltage ControlDram Clock Dram CAS Latency Precharge to Active Trp Dram Command RateBank Interleave Active to Precharge Tras CPU Clock Dram VoltageSpread Spectrum Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor / User Password Bios Setup Save & Exit Setup Exit Without Saving Chapter Driver Installation Getting Started Driver UtilitiesRunning the Driver Utilities CD CD Content Chapter