Philips SBCVL1200 manual Testing, Installing the remote control extender cord, General notes

Testing

Step 1: testing the video signal

You should now see the video source you selected on your second TV. It may be necessary to reposition the Receiver unit to make sure the built-in antenna gives the best quality picture. Repositioning the Transmitter unit, centimetre by centimetre over the surface on which it’s positioned, can also help to improve the quality.

Step 2: testing the remote control extender

Try out the remote control to make sure it is working correctly. Point the remote control of the video source you are watching at the Receiver unit and change the programme number or press Play and then Stop. A red light (figure A-7) flashes on the Receiver unit indicating that it has received the remote control command. On the Transmitter unit a red light (figure B-13) flashes to indicate that it is sending the extended remote control command to the video sources.

If no red light flashes on the Transmitter unit it may be necessary to reposition either of the remote control antennas on the rear of the Receiver unit (figure A-8) or Transmitter unit (figure B-15). The red light on the Transmitter unit should now flash when a remote control command is given at the receiver.

If the video source does not respond to the given remote control command please install the remote control extender cord.

Installing the remote control extender cord

A cord with two IR eyes and a jack plug is provided to deliver the signals from the Transmitter unit to the video sources you wish to control.

•Ensure that the Transmitter unit is switched off.

•Plug the jack plug into the socket (figure B-2) marked IR at the back of the Transmitter unit.

•Locate the IR sensor on the video source (refer to the video sources Instructions for Use).

If you cannot identify the IR sensor on the video source do the following:

-Ensure that both Transmitter and Receiver units are switched on.

-Ask another person to press and hold a key of the video source’s remote control while pointing it at the Receiver unit. (Both A-7 and B-13 must be flashing)

-While they are doing this, slowly move an IR eye along the front panel of the video source. The distance between the IR eye and the front panel should not exceed 1 centimetre.

-When the video source reacts to the command from the remote control you have found the correct position.

•Remove the adhesive tape from the back of the IR eye and stick the eye onto the IR sensor window of the video source.

•If necessary, repeat the procedure for the second video source.

Note

!Instead of sticking the IR eye onto the device you can also try to place the IR eye 5-10 cm in front of the device, which makes finding the exact location less critical.

!It is possible that particular brands and types of TV react to remote control signals by making a buzzing noise when a command is given. Refer to the Troubleshooting section if you are still having problems getting your configuration to work correctly.

General notes

!The picture and sound quality will be influenced by the use of microwave ovens. Other wireless systems (Bluetooth, wireless LANs, etc.) can also adversely influence the quality of picture and sound.

!The Wireless TV Link is a Radio Frequency (RF) based product. As such its performance can suffer the same kinds of interference as GSMs, portable radios and other RF-based products.

!If the same video source is selected for both TVs, then you get the same programme on each TV.

!The Wireless TV link is not limited to just one room or house. You can use it anywhere in or around the house. Consequently, anybody in the vicinity of your house (up to the maximum operating range) who also owns a Wireless TV link set to the same channel, can watch the same programmes that are playing on your video source.

!Separate Philips Wireless TV Link Receivers (SBC VL1205) are available and allow you to receive the video signal transmitted by a Philips Wireless TV link in another location. You can, for example, use the Philips SBC VL1200 Wireless TV Link in your living room to watch a programme on a second TV in your bedroom. A separate receiver allows you to watch the same transmitted video signal in another location (e.g. the TV in your study), regardless of how many other receivers you might have.

!In order to prohibit the mixing up of remote control commands it’s not advisable to use a TV as a video source.

!Some built-in VCRs (TV-VCR combination) cannot be used with the Transmitter unit of the Wireless TV link (depends on brand and type).

!If you wish to leave the original remote controls with your video sources, Philips has a complete range of Universal Remote Controls that cover all the equipment you want to operate, regardless of brand or age.

!The remote control extender operates within the 32kHz to 40kHz range. Video sources operating outside this range cannot be controlled remotely via the remote control extender.

!The Wireless TV Link’s Transmitter unit can support the channel downloading feature of high- end TVs and VCRs. (This channel downloading feature is also known as ‘Follow-TV’, ‘Easylink’, ‘SmartLink’, ‘AV-Link’, ‘MEGALogic’, ‘TV-Link’ or ‘Q-Link’). Fully wired SCART cables that support this feature must be purchased separately. Please note that both your TV and VCR must support this feature.

!The Wireless TV Link does not support P50 ‘what you see is what you record’ functionality.

!Radio wave safety: When switched on, the Philips Wireless TV Link transmits and receives radio waves. The Philips Wireless TV Link complies with the standards that are defined for it.

!The Philips Wireless TV Link has an operating range of up to 100 metres in open air. Walls, ceilings and other large objects may limit the useable operating range to about 30 metres in the house.

6 7