Place the TV/VCR/ACC | Philips TS3659C1 specs

SETTING THE REMOTE CONTROL TO OPERATE ACCESSORY DEVICES

Search Method

Your TV remote can be set to work various accessory

devices such as VCRs, Cable Boxes, Satellite Receivers, DBS, DVD, etc. by using the search method.

If the Direct Access method shown on page 37 did not set your remote to work your acces- sory device, follow the easy steps listed below.

Please read steps 1-4 before beginning.

BEGIN

Turn ON the device by press- ing the POWER button on the

device you are attempting to pro- gram.

Place the TV/VCR/ACC

Mode Switch in the proper posi-

tion.

Press and hold the VCR RECORD and the SMART SOUND buttons simultaneous- ly.

The device will begin to change channels after the remote identifies the correct code. When the channels start to change, release the VCR RECORD and SMART SOUND buttons. The remote should be ready to oper- ate the device.

SMART HELP

This method can take up to two minutes to perform.

Don’t let the device change more than five channels after the remote identifies the code. If you do, the remote may pass up the right code; another two minute search cycle will have to be repeated.

If no channel change happens within two minutes, repeat steps 1-4. Should a channel change still not occur, the remote will not work the desired device.

Satellite Receiver,

DBS, DVD,

or similar device

Cable Converter		070809 06		07
1				07
1				0809
		06	0708	0809
VCR			09
			09
2	SLEEP		POWER	4
2	AV	STATUS/EXIT CC	TV/VCR-CLOCK
TV	AV	STATUS/EXIT CC	TV/VCR-CLOCK
VCR VCR		INCREDIBLE MULTI	A/CH

ACC RECORD STEREO MEDIA

3

SMARTSMART

SOUNDPICTURE

MENUSURF

3

VOL

CH

MUTE

38

Image 38

Philips TS3659C1 manual Setting the Remote Control to Operate Accessory Devices, Place the TV/VCR/ACC

Contents

TS3659C1 Warranty Verification Safety Instructions Read before operating equipment Table of Contents Features Cable/Antenna Adjusting the TV Picture Tings are at normal mid-range levels Press the Numbered buttons Setting the TV’S ClockTimer controls Press the STATUS/EXIT but Activating the TV’S on Timer Control Press the Menu button on Selecting the TV’S on Timer Channel Press the STATUS/EXIT button Setting the TV’S on Timer Start Time Turning on the on Timer Display Press the Cursor Down Understanding Smartlock Movie Ratings Down to highlight Using Smartlock Setting UP the Access CodeEnter current access code SmartLock control This stops the viewing of VCR, DVD, etc Using Smartlock Blocking ChannelsPress the Channel + or Select block Press the Cursor Right Button to access the movie ratings Using Smartlock Movie RatingEnter the correct access code number. Xxxx shows on Press the STATUS/EXIT but- ton to remove the menu Using Smartlock TV Rating Using Smartlock Blocking Options Left button to set Using Smartlock Block UnratedButton or the Cursor Block Unrated to on or Left button to set no Using Smartlock no RatingPress the Menu button on the remote to show the on-screen Rating to on or OFF Reviewing the Smartlock Settings Example Blocking is set to OFF Viewing Blocked Programming Xxxx Turning on the Noise Reduction Control Press the Cursor UP or Cursor Down buttons to Turning on the Contrast + Control Trast + control Press the Cursor Right Using the Closed Caption Control Mode Using the Sleep Timer Control Good BYE Sleep Adjusting the TREBLE, BASS, and Balance Sound Controls On a selected show and the TV is Setting the TV for Stereo and SAP ProgramsRemember, if stereo is not present Placed in the Stereo mode, the sound com Round Using the Incredible Stereo ControlUsing the Volume BAR Control Tial Use the Cursor Left or Right buttons to set Setting the Audio OUT ControlAudio OUT Press the Cursor Down button to select the Speakers Using the TV Speaker Control and Audio Output JacksConnect the Right and Left Use the Cursor Right or Cursor Left buttons Using the AUDIO/VIDEO Input Jacks Connect the Video yellow Turn the VCR or Digital Using the AUDIO/VIDEO Input Jacks CONT’DConnect the S-VIDEO Using the Smart Picture Control Using the Smartsound Control Press the Smart Sound but Using the Channel Surf Control Remote control number for your Find your Three-Digit Code on pages Direct Access Method Place the TV/VCR/ACC Setting the Remote Control to Operate Accessory DevicesTurn on the device by press- ing the Power button on Remote Control Direct Entry Codes Remote VCR Code no Remote Dvdcode no Using the REMOTE’S VCR Buttons TV Displays Wrong Channel or No Channels Above Tips if Something Isnt Working Glossary to Television Terms Index Philips Consumer Electronics Company Texas Page Limited Warranty