CH3 CH4, Plug in the TV and the VCR | Philips VRA211AT specification

Hookups Without a Cable Box / Direct Broadcast System (cont’d) 7

3

Connect the RF coaxial cable (supplied) to the OUT Jack on the back of the VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on

type (supplied) or screw-on type of coaxial cable, whichever you prefer.)

Antenna or Cable

ANT

IN

				AUDIO
			ANT	OUT IN	OUT
			ANT	VIDEO	CH3 CH4
			IN		75V
					75V
					ANT	/
AUDIO					CABLE
AUDIO
OUT	IN		OUT			ANTENNA IN Jack
						ANTENNA IN Jack
VIDEO		CH3	CH4			(on back of TV)
		CH3	CH4		RF coaxial cable	example only
						example only

4

Plug in the TV and the VCR.

5

Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever channel is not used or least used in your area. Set the TV to the same channel. For example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on channel 03.

	CH	4
	or	3
	CH	3
	CH

CH3 / CH4

Switch

CH3 CH4

ANT

IN

ANT

IN

AUDIO

OUT

IN

OUT

VIDEO CH3 CH4

AUDIO
OUT	IN	OUT
VIDEO		CH3 CH4

6

You are ready to turn on the VCR. Please go to page 11 before turning on the VCR.

Image 7

Philips VRA211AT owner manual CH3 CH4, Plug in the TV and the VCR

Contents

VRA211AT Model No Serial No Dear Philips Magnavox product ownerFor Customer Use This bolt of lightning indi- cates uninsulated material Safety Precautions FeaturesIntroduction Table of Contents Removing the Plastic Cover from the Front Panel Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenance Disconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast System Plug in the TV and the VCR CH3 CH4 RF coaxial Cable TV’s ANTENNAJack Cable Signal RF coaxialConnections Recording/Viewing Any Channel Cable Box/DBS Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Recording One Channel/Watching Another Hookups With a Stereo TV Press the Menu button. The display shown below will appear Press the VCR button, then press the Power buttonTurning on Your VCR 2Turn on the TV Press the VCR button Automatic Channel SetupPress the Menu button Adding/Deleting Channels Automatic Channel Setup cont’d Press the VCR button Press the Menu button Reviewing Memorized ChannelsPress the STATUS/EXIT button once or twice to exit Enter a 0 before a single-digit number Setting the Clock Daylight-Savings Time Language Selection Remote Control Buttons Remote Control Buttons cont’d If you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only on VCR Display Panel Front Panel Rear Panel Read and follow the steps below to play a tape Playing1Turn on the TV 2Insert a tape in the VCR VCR light does not appear, press the VCR/TV button once RecordingInsert a tape with its record tab intact in the VCR If the VCR light appears on the display panel, go to . If VCR light will disappear from the VCR’s display panel Recording One Channel/Watching Another One-Touch Recording Daily Timer RecordingDo each step within 60 seconds of the previous step Press the VCR button, then press the Menu button Timer Recording cont’d Press the STATUS/EXIT button. Program WAS COM Timer Recording cont’dTape Speeds Timer recording information for the program in the lowest Checking or Cancelling Timer RecordingsProgram REVIEW, then press the F.FWD/B button RF coaxial cable Rerecording Tape Duplication Press the F.FWD/B button so that on appears beside Repeat Play Real-Time Counter Memory Button to reset the real-time counter to zeroWhile the status display is on-screen, press the Clear Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLP Automatic Operation Features Cable Box/DBS Output Channel 03 or Glossary Helpful Hints Helpful Hints cont’d Specifications Model # Serial # Limited Warranty Index Page Supplied Accessories