Rear Panel | Philips VRA211AT specs

Rear Panel 23

ANT(enna) IN Jack

Connect your antenna or cable here. Details are on pages six-10.

AUDIO IN Jack

Connect a cable coming from the AUDIO OUT Jack of a camcorder, another VCR, or an audio source here. Details are on page 32.

AUDIO OUT Jack

Connect a cable going to the AUDIO IN Jack of a camcorder, another VCR, or an audio system here. Details are on page 32.

ANT

		IN
AUDIO
OUT	IN	OUT
		OUT
VIDEO		CH3 CH4
VIDEO

VIDEO OUT Jack

Connect a cable going to the VIDEO

IN Jack of a camcorder, another

VCR, or an audio-visual system

(laser disc player, video disc player,

etc.) here. Details are on page 32.

CH3/CH4 Switch

Set to channel 3 or 4

VIDEO IN Jack

to use your TV with

your VCR. Details are

Connect a cable coming from the

on pages six-nine.

VIDEO OUT Jack of a cam-

AC Power

Cord

corder, another VCR, or an

Connect to a stan-

audio-visual source (laser disc

OUT Jack

dard AC outlet to

player, video disc player, etc.)

Use the supplied RF coaxi-

supply power to the

here. Details are on page 32.

al cable to connect this

VCR.

jack to the ANTENNA IN

Jack on your TV, Cable

Box, or Direct Broadcast

System. Details are on

pages six-nine.

Image 23

Philips VRA211AT owner manual Rear Panel

Contents

VRA211AT Model No Serial No Dear Philips Magnavox product ownerFor Customer Use This bolt of lightning indi- cates uninsulated material Introduction FeaturesSafety Precautions Table of Contents Removing the Plastic Cover from the Front Panel Putting Batteries in the Remote ControlUsing the Remote Control VCR maintenance Disconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast System Plug in the TV and the VCR CH3 CH4 RF coaxial Cable TV’s ANTENNAJack Cable Signal RF coaxialConnections Recording/Viewing Any Channel Cable Box/DBS Cable SignalConnect a Cable signal to the VCR’s ANTenna in Jack Recording One Channel/Watching Another Hookups With a Stereo TV Press the Menu button. The display shown below will appear Press the VCR button, then press the Power buttonTurning on Your VCR 2Turn on the TV Press the Menu button Automatic Channel SetupPress the VCR button Adding/Deleting Channels Automatic Channel Setup cont’d Press the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsPress the VCR button Press the Menu button Enter a 0 before a single-digit number Setting the Clock Daylight-Savings Time Language Selection Remote Control Buttons Remote Control Buttons cont’d If you select Status ON, then select Counter only OFF On-Screen Status DisplaysStatus Display example only If you select Status ON, then select Counter only on VCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingRead and follow the steps below to play a tape VCR light does not appear, press the VCR/TV button once RecordingInsert a tape with its record tab intact in the VCR If the VCR light appears on the display panel, go to . If VCR light will disappear from the VCR’s display panel Recording One Channel/Watching Another One-Touch Recording Daily Timer RecordingDo each step within 60 seconds of the previous step Press the VCR button, then press the Menu button Timer Recording cont’d Tape Speeds Timer Recording cont’dPress the STATUS/EXIT button. Program WAS COM Program REVIEW, then press the F.FWD/B button Checking or Cancelling Timer RecordingsTimer recording information for the program in the lowest RF coaxial cable Rerecording Tape Duplication Press the F.FWD/B button so that on appears beside Repeat Play While the status display is on-screen, press the Clear Button to reset the real-time counter to zeroReal-Time Counter Memory Viewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLP Automatic Operation Features Cable Box/DBS Output Channel 03 or Glossary Helpful Hints Helpful Hints cont’d Specifications Model # Serial # Limited Warranty Index Page Supplied Accessories