Pioneer CDJ-100S Others Troubleshooting, Error display, 800, Pioneer Electronics of Canada, Inc

				OTHERS: TROUBLESHOOTING
Symptom		Cause		Remedy
When the auto cue function is	Ö	If the sound muted portion between	Ö Press TIME MODE/AUTO CUE button for
set ON, track search is not fin-		selections is long, searching time will		more than 1 second to set the auto cue
ished.	Ö	be long.		function OFF.
		If the sound muted portion is re-
		corded for about 20 seconds or more,
		playback will start without the auto
		cue function.
Back cue function cannot be	Ö	The cue point is not set yet.	Ö	Set the cue point. (See page 10.)
carried out even though the
CUE button is pressed in play-
back mode.
DJ mode doesn't work.	Ö	DIGITAL OUT switch is set to ON (dig-	Ö	Set DIGITAL OUT switch to OFF.
		ital output is effective).
The picture of the TV screen is	Ö	Interference is being picked up from	Ö Turn off POWER of the player, or move
fluctuated or FM broadcast is		the CD player.		the player away from the TV or tuner.
interfered with noise.
The disc is not rotating when	Ö	The disc rotation stops automatically	Ö Playback can be started by pressing the
power is ON.		if no operation has been performed		PLAY/PAUSE button. Press the EJECT
		for 80 minutes or more in pause		button to eject the disc.
		mode.

¦Static electricity and other external effects may cause this unit to malfunction. In this case, set the power switch to OFF, then switch it on again after the disc has come to a complete stop.

¦This unit cannot playback non-finalized CD-R discs (partial discs).

¦This component is designed to play both ordinary 12 cm (5-inch) discs and 8 cm (3-inch) discs mounted on adapters. Non-round (eccentrically shaped discs) cannot be played, since damage or malfunction may result.

Error display

When the player detects an error during operation, if will immediately stop and display an error code in the display window. Check the error code with those listed in the table below to determine the cause of error. Contact your nearest Pioneer authorized service center if the cause of the error is unknown, too difficult to fix or if the same error code continues to display after the remedy has been tried. Refer to the error code when speaking to the Pioneer service representative.

Displayed error	Type of error		Error contents	Possible Cause = Remedy
code number
E-72 01	TOC READ ERROR	TOC date cannot be read after 20 seconds.		Disc has scratch
				= Replace disc
E-72 02	FG PULSE ERROR	Disc is rotating, but rotation cannot be ascer-
				Disc is dirty
		tained.
				= Clean disc
E-83 01	PLAYER ERROR	Disc loaded cannot be played properly.
E-83 02	PLAYER ERROR	Disc loaded cannot be played properly.
E-91 01	MECHANICAL TIME OUT	Mechanical operation did not end in allotted		Foreign object is in disc com-
		time.		partment slot.
				= Remove it.
E-91 03	MECHANICAL TIME OUT	Mechanical operation did not end in allotted
		time.
Should this product require service in the U.S.A. and you			Should this product require service in Canada, please con-
wish to locate the nearest Pioneer Authorized Independent			tact a Pioneer Canadian Authorized Dealer to locate the
Service Company, or if you wish to purchase replacement			nearest Pioneer Authorized Service Company in Canada.
parts, operating instructions, service manuals, or			Alternatively, please contact the Customer Service Depart-
accessories, please call the number shown below.			ment at the following address:
	800 – 872 – 4159		Pioneer Electronics of Canada, Inc.
Please do not ship your product to Pioneer without first			300 Allstate Parkway
calling the Customer Service Department at the above
listed number for assistance.			Markham, ON L3R 0P2
PIONEER ELECTRONICS SERVICE, INC.			(905) 479-4411
CUSTOMER SUPPORT DIVISION
P.O. BOX 1760, LONG BEACH,			For warranty information please see the Limited
CA 90801-1760, U.S.A.			Warranty sheet included with your product.
For warranty information please see the Limited Warranty
sheet included with your product.
				15
				<DRB1232>
				En