Setting Up the System
Setup after Connection
After components have been connected to INPUT1 or INPUT2,
Follow the procedure described below and make settings as they apply to the type of components connected.
Screen Mode setup
Note
These settings are required only when using the following input signal refresh rates: 1 31.5 kHz horizontal / 60 Hz vertical; 2
48.4kHz horizontal / 60 Hz vertical; 3 56.5 kHz horizontal / 70 Hz vertical. No manual setup is necessary for signals with other refresh rates, since adjustments are performed automatically (the SETTING item will not be displayed).
1Switch MAIN POWER on the connection panel to the on position to turn on the unit’s main power. The STANDBY/ON indicator lights red.
2Press STANDBY/ON to put the unit in the operation mode.
The STANDBY/ON indicator turns green.
3Select INPUT1 or INPUT2.
4Press MENU to display the menu screen. The menu screen appears.
MAIN MENU |
|
|
|
|
| INPUT1 |
PICTURE | SCREEN | SET UP | OPTION | |||
C O N T R A S T |
| : | 0 |
|
|
|
BR I GHT . |
| : | 0 |
|
|
|
R. L E V E L |
| : + 6 0 |
|
|
| |
G. L E V E L |
| : + 6 0 |
|
|
| |
B. L E V E L |
| : + 6 0 |
|
|
| |
H. E NHAN CE | : | 0 |
|
|
| |
V . E NHAN CE | : | 0 |
|
|
| |
RE S E T |
|
|
|
|
|
|
SELECT |
| SET | ENTER | MENU | EXIT | |
5Press 2/3 to select SET UP.
MAIN | MENU |
|
|
|
|
| INPUT1 |
PICTURE | SCREEN | SET UP | OPTION | ||||
| I N P UT L A B E L |
| : I N P UT 1 | ||||
| POWE R | MA NAGEME NT : OF F |
|
| |||
| C L AMP | P O S I T I O N | : A U T O |
|
| ||
| S E T T I N G |
| : V G A |
|
| ||
| SELECT | SET | ENTER | MENU | EXIT | ||
6 Press 5/∞ to select SETTING, then press SET. | English | |||||||
MAIN | MENU |
|
|
|
|
| INPUT1 | |
|
|
|
|
|
| |||
PICTURE | SCREEN | SET UP | OPTION |
| ||||
| I NP UT L A B E L |
| : I NP UT 1 |
| ||||
| POWE R | MA NAGEME NT : OF F |
|
|
| |||
| C L AMP | P O S I T I O N | : A U T O |
|
|
| ||
| S E T T I N G |
| : V G A |
|
|
| ||
| SELECT | SET | ENTER | MENU | EXIT |
| ||
7Press 2/3 to select the display mode.
S E T T I N G : V G A
SELECT SET SET MENU EXIT
1When the input signal has a refresh rate of 31.5 kHz (horizontal) and 60 Hz (vertical), pressing 2/3 will cause the display mode to change alternately as follows:
|
| PC AUTO |
| VGA |
|
|
| |||
|
|
|
|
| ||||||
|
|
| WIDE VGA |
|
|
|
| |||
|
|
|
|
|
| |||||
2 When the input signal has a refresh rate of 48.4 |
| |||||||||
kHz (horizontal) and 60 Hz (vertical), pressing 2/3 |
| |||||||||
will cause the display mode to change alternately |
| |||||||||
as follows: |
|
|
|
|
| System | ||||
|
| PC AUTO |
| XGA |
|
| ||||
|
|
|
|
|
| |||||
|
|
| WIDE XGA |
|
| the | ||||
|
|
|
| |||||||
3 When the input signal has a refresh rate of 56.5 | ||||||||||
Up | ||||||||||
kHz (horizontal) and 70 Hz (vertical), pressing 2/3 | ||||||||||
Setting | ||||||||||
will cause the display mode to change alternately | ||||||||||
| ||||||||||
as follows: |
|
|
|
|
|
| ||||
|
| XGA | WIDE XGA |
| ||||||
|
|
|
|
|
|
|
|
|
| |
If the PC AUTO setting is selected when using the above PC input signals, screen resolution will automatically switch between VGA/WVGA or XGA/WXGA.
Note
The PC AUTO setting supports automatic signal selection only when using RGB separate Sync inputs. When G ON SYNC or Composite Sync signals are input, selecting PC AUTO will cause the screen resolution to be set to VGA
or XGA only. When using a G ON SYNC or Composite SYNC signal for WIDE VGA or WIDE XGA inputs, set the screen display mode manually.
8When the setup is completed, press MENU to exit the menu screen.
Note
Make this setup for each input (INPUT1 and INPUT2).
17
En
