Pioneer PRV-9200 Recording the Copy List, HDD to DVD Copy List commands, Add

Copying and back-up

•Chapter Edit (Chpt Edit) – Edit chapters within a Copy List title (see page 66):

•Erase – Erase a chapter.

•Divide – Divide a chapter into two.

•Combine – Combine two chapters into one.

•Move – Change the chapter order.

•Preview – Check the chapter content.

•Erase Section (Erase Sec) – Erase a section of a title in the Copy List (see page 68).

•Confirm List (Conf List) – Confirm the Copy List and go to the recording settings screen (see Recording the Copy List below).

Recording the Copy List

After putting together your Copy List, you’re ready to record it.

1Select ‘Conf List’ to display the Copy List settings screen.

2 Use the	(cursor left/right) buttons to select
the Recording Mode.
HDD to DVD Copy
HDD
	HDD DVD-RW VIDEO	Required 0h08m
	Recording Mode	High Speed
Add		Start
Erase	Copy List Total	1175MB
Ttl Name
	Current DVD Remain	2830MB
Divide
		/ 4700MB
Combine
Conf List

•High-Speed Copy – The Copy List is copied at the same recording quality as the original. (See page 59 for more information on high-speed copying.)

•FINE, SP, LP, EP, MN – The Copy List is copied at the specified recording quality in real-time. (Note that if you copy at a higher quality setting than the original, the copy will not be better quality than the original.)

If you select MN above, you can also change the level setting (MN1–MN32) from the Recording Quality box that appears.

•Optimized – The recording quality is automatically adjusted so that the Copy List fits on to the space available on the disc. Copying is carried out in real- time.

When you change the recording mode setting, you can see how much disc space it will require. If this is more than is available, it shows up in red and you won’t be able to start copying. In this case, either change the recording quality, or press RETURN to go back to the Copy List screen and erase one or more titles from the Copy List.

07

3 Select ‘Start’ to begin copying.

Note

•When the copy mode is set to something other than High-Speed Copy for copying to a Video mode DVD, the chapter markers of the original are not copied.

Chapter markers are put into the copy at regular intervals, according to the Auto Chapter setting (see also Auto Chapter (Video) on page 104).

HDD to DVD Copy List commands

Add

Use this command to add titles to the Copy List.

1 Select ‘Add’ from the Copy List menu options.

2 Use the (cursor left/right) buttons to select a title from the HDD to add to the Copy List, then press ENTER.

HDD to DVD Copy

All

HDD 1 2 3 4

HDD

		8/11Sun 4:00PM	2ch LP	1/3
Add		Recording Time	0h32m55s
	DVD 1	2	3
Erase				4
Ttl Name
Divide		Copy List	Total 1h30m	1/2
Combine

Conf List

The thumbnail appears in the Copy List section in the lower half of the screen. If there are already titles in the Copy List, the title is added at the end.

3Repeat step 2 to add more titles to the Copy List, or press RETURN to go back to the Copy List menu options.

Note

•When Frame Accurate is set to Off (see Frame Accurate on page 104), the following limitations on adding titles to the Copy List apply:

–When adding titles that contain copy-once protected material, the copy-once parts will not be added to the Copy List.

–When adding titles that contain material of more than one aspect ratio (screen size), each part with a different aspect ratio will be added as a separate title.

–Widescreen material recorded in LP, EP or MN1–18will not be added to the Copy List.

–Chapter markers on the copy may be up to 0.5 seconds off compared to the original.

63

En