Using other functions | 09 |
Resetting the system
Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this. Set
MULTI ZONE OFF.
!Disconnect the iPod and USB memory device from the receiver beforehand.
!Set the Control with HDMI to OFF (see HDMI Setup on page 45 ).
1Switch the receiver into standby.
2While holding down ENTER on the front panel, press uSTANDBY/ON. The display shows RESET cNO d.
3Select ‘RESET’ using PRESET k/l, then press ENTER on the front panel. The display shows RESET? OK.
4Press ENTER to confirm.
OK appears in the display to indicate that the receiver has been reset to the factory default settings.
!Note that all settings will be saved, even if the receiver is unplugged.
Default system settings
Setting | Default | ||
Digital Video Converter | ON | ||
SPEAKERS | SB/FH | ||
Speaker System | Normal | ||
(SB/FH) | |||
|
| ||
| Front | SMALL | |
| Center | SMALL | |
Speaker Setting | FH/FW | SMALL | |
Surr | SMALL | ||
| |||
| SB | SMALLx2 | |
| SW | YES | |
Surround Position | IN REAR | ||
Crossover | 80 Hz | ||
OFF | |||
DIMMER | Brightest | ||
Inputs
See Input function default and possible settings on page 27 .
HDMI
HDMI Audio |
| Amp |
Control |
| ON |
Control Mode |
| PQLS |
Display Power Off |
| NO |
Audio playback |
|
|
Power On Level |
| LAST |
Volume Limit |
| OFF |
Mute Level |
| FULL |
Phase Control |
| ON |
| iPod/USB, |
|
| HOME MEDIA |
|
Auto Sound | GALLERY, | ON |
ADAPTER PORT |
| |
Retriever |
| |
input function |
| |
|
| |
| Other input | OFF |
| functions | |
|
| |
Sound Delay |
| 0.0 frame |
Dual Mono |
| CH1 |
Setting |
| Default | |
DRC |
| AUTO | |
SACD Gain |
| 0 dB | |
LFE Attenuate |
| 0 dB | |
Auto delay |
| OFF | |
Digital Safety |
| OFF | |
Effect Level | ExtendedStereo | 90 | |
Other modes | 50 | ||
| |||
2PL II Music | Center Width | 3 | |
Dimension | 0 | ||
Options | |||
Panorama | OFF | ||
| |||
|
| Neo:6 | |
Neo:6 Options | Center Image | CINEMA: 10 | |
Neo:6 | |||
|
| ||
|
| MUSIC: 3 | |
2PL IIz Options | Height Gain | MID | |
| Listening Mode | AUTO | |
All Inputs | (2 ch/multi ch) | SURROUND | |
Listening Mode | STEREO | ||
| |||
| (Headphones) | ||
|
|
See also Setting the Audio options on page 48 for other default DSP settings.
MCACC
MCACC Position Memory | M1: | ||
MEMORY 1 | |||
|
| ||
Channel Level (M1 to M6) | 0.0 dB | ||
Speaker Distance (M1 to M6) | 10’00’’ | ||
Standing Wave | ATT of all | 0.0 dB | |
channels/filters | |||
(M1 to M6) |
| ||
SWch Wide Trim | 0.0 dB | ||
| |||
EQ Data (M1 | All channels/ | 0.0 dB | |
bands | |||
to M6) |
| ||
EQ Wide Trim | 0.0 dB | ||
| |||
En 53