The System Setup and Other Setup menus 12

Primary DNS Server/

Secondary DNS Server

In case there is only one DNS server address provided by your ISP on paper, enter it in the ‘Primary DNS Server’ field. In case there are more than two DNS server addresses, enter ‘Secondary DNS Server’ in the other DNS server address field.

Proxy Hostname/Proxy Port

This setting is required when you connect this receiver to the Internet via a proxy server. Enter the IP address of your proxy server in the ‘Proxy Hostname’ field. Also, enter the port number of your proxy server in the ‘Proxy Port’ field.

1Select ‘IP Address, Proxy’ from the Network Setup menu.

2Select the DHCP setting you want. When you select ON, the network is automati- cally set up, and you do not need to follow Steps

3.Proceed with Step 4.

If there is no DHCP server on the network and you select ON, this receiver will use its own Auto IP function to determine the IP address.

!The IP address determined by the Auto IP function is 169.254.X.X. You cannot listen to an Internet radio station if the IP address is set for the Auto IP function.

3Enter the IP Address, Subnet Mask, Default Gateway, Primary DNS Server and Secondary DNS Server.

Press i/j to select a number and k/l to move the cursor.

4Select ‘OFF’ or ‘ON’ for the

Enable Proxy Server setting to deactivate or activate the proxy server.

In case you select ‘OFF’, proceed with Step 7. In case you select ‘ON’, on the other hand, proceed with Step 5.

5Enter the address of your proxy server or the domain name.

Use i/j to select a character, k/l to set the position, and ENTER to confirm your selection.

6Enter the port number of your proxy server.

Use i/j to select a character, k/l to set the position, and ENTER to confirm your selection.

7Select ‘OK’ to confirm the IP Address/ Proxy setup.

Network Standby

This setting allows the AVNavigator or iContro- lAV2 function for operating the receiver from a computer connected on the same LAN as the receiver to be used even when the receiver is in the standby mode.

1Select ‘Network Standby’ from the Network Setup menu.

2Specify whether the Network Standby is ON or OFF.

!ON – The AVNavigator or iControlAV2 function can be used even when the receiver is in the standby mode.

!OFF – The AVNavigator or iControlAV2 function cannot be used when the receiver is in the standby mode (This lets you reduce power consumption in the standby mode).

Friendly Name

1Select ‘Friendly Name’ from the Network Setup menu.

2Select ‘Edit Name’ then select ‘Rename’.

If after changing the name you want to restore the name to the default, select Default.

3Input the name you want.

Use i/j to select a character, k/l to set the position, and ENTER to confirm your selection.

Parental Lock

Set restrictions for using Internet services. Also set the password accompanying the usage restrictions.

!Upon shipment from the factory, the password is set to “0000”.

Important

When the HOME MEDIA GALLERY input is selected, the setting made here cannot be reflected. Set the input to something other than HOME MEDIA GALLERY before making this setting.

1Select ‘Parental Lock’ from the Network Setup menu.

2Input the password.

Use i/j to select a character, k/l to set the position, and ENTER to confirm your selection.

3Specify whether to turn Parental Lock on or off.

!OFF – Internet services are not restricted.

!ON – Internet services are restricted.

4If you want to change the password, select Change Password.

In this case, the procedure returns to step 2.

Port Number Setting

On this receiver, there can be up to 5 numbers of ports where signals are received. One of these, port 8102 which used for communicating with iControlAV2, cannot be changed, but the desired number can be set for the 4 other ports.

1Select ‘Port Number Setting’ from the Network Setup menu.

2Select the port number you want to change.

3Input the port number.

!Use i/jto select a character, k/lto set the position, and ENTER to confirm your selection.

!It is not possible to set the same port number more than once.

4If there are other port numbers you want to change, repeat steps 2 and 3.

Note

!When the wireless LAN converter (AS-WL300) is connected, the port number cannot be set to port 3.

!We recommend setting the port number to 23 or within the range of 49152 to 65535.

!When the port number is changed, network communications between the receiver and AVNavigator are no longer possible. In this case, click Settings on the AVNavigator’s function menu, select the IP Address tab and input one of the port numbers set on the receiver side to enable communications with AVNavigator.

Wireless LAN Converter

This setting is required for connecting a wireless LAN converter to the receiver and using wireless network functions.

For the wireless LAN converter, use the separately sold AS-WL300.

Access Point Setting

Make the connection settings for the wireless LAN converter connected to the receiver and the access point. Connect the wireless LAN converter to the receiver and set DHCP on the “IP Address, Proxy” settings menu beforehand (page 68). There are four way to make the settings for connecting to the access point, as shown below.

En 69