10Controlling the rest of your system
Controlling the rest of your system
Note
! You can cancel or exit any of the steps by |
Setting the remote to control other components
About the Remote Setup menu
The Remote Setup mode is set by pressing the number button while pressing RCU SETUP. The different items on the Remote Setup menu are described below. For their setting procedures, refer to the explanations for the respective items.
Setting What it does
Preset codes can be set for the various input functions. The remote control codes of a number of other devices
Preset (including products of other brands)
recall are preset in the remote control to allow these devices to be operated. See Selecting preset codes directly on page 55 .
If the desired operations cannot be performed even though you have set
Code the preset codes, the remote control learning signals of other devices can be learned
directly. See Programming signals from other remote controls on page 55 .
A series of the remote control operations for starting listening or viewing
Multi can be programmed. Multiple remote operation control codes can be set for the differ-
ent input functions. See Multi Operation and System Off on page 56 .
This is a function for automatically turning off the power of devices con-
System nected to the receiver. Multiple remote
off control codes can be set, as desired. See Multi Operation and System Off on page 56 .
Setting | What it does | |
| This is a setting for changing only the | |
| remote control unit’s operation screen, | |
| without changing the receiver’s input, | |
Direct | when the remote control unit’s input | |
function buttons are pressed. This | ||
function | ||
is convenient for using the remote | ||
| ||
| control unit for devices not connected | |
| to the receiver. See Direct function on | |
| page 56 . | |
| This function is used to erase remote | |
| control codes that have been learned. | |
Erase | Codes learned for the different input | |
learning | functions can be erased individually. | |
| See Erasing one of the remote control | |
| button settings on page 55 . |
The backlight lighting pattern can be selected from among four modes, in
Back light consideration of convenience and battery service life. See Setting the backlight mode on page 56 .
This is a function for resetting preset codes that have been set. Key reset-
Reset ting can be done for individual input function functions. See Erasing all learnt settings that are in one input function on
page 55 .
This is a function for resetting all remote control unit settings you have
All reset made to the defaults set upon shipment from the factory. See Resetting the remote control settings on page 57 .
If you have multiple Pioneer receivers, amplifiers, etc., this setting can be
Change used to prevent other units from oper- RC mode ating simultaneously when the remote control unit is operated. See Operating
multiple receivers on page 54 .
pressing RCU SETUP. |
! After one minute of inactivity, the remote |
automatically exits the operation. |
Operating multiple receivers
Up to four receivers can be operated discretely using this receiver’s remote control when using multiple receivers, provided they are of the same model as this receiver. The receiver to be operated is switched by inputting the preset code to set the remote control setting.
!Set the remote modes on the receivers before using this function (see Remote Control Mode Setup on page 71 ).
1Press and hold RCU SETUP, then press ‘4’ for three seconds.
Release the button after the LED flashes once. The LED continues to flash.
!To cancel the preset setup mode press
RCU SETUP.
2Press the number button for the receiver (“Receiver 1” to “Receiver 4”) you wish to operate.
For example, to operate “Receiver 2”, press ‘2’. If the LED lights for one second and continues to flash, the setting has been successfully completed.
When the preset code is input, the LED flashes three times to indicate that the setting has failed.
Most components can be assigned to one of the input function buttons (such as DVD or CD) using the component’s manufacturer preset code stored in the remote.
However, there are cases where only certain functions may be controllable after assigning the proper preset code, or the codes for the manufacturer in the remote control will not work for the model that you are using.
If you can’t find a preset code that matches the component you want to control, you can still teach the remote individual commands from another remote control (see Programming signals from other remote controls on page 55 ).
!For greater convenience, assign the TV connected to the MONITOR OUT terminal to the TV CTRL button, and assign your satellite/ cable receiver or
!Devices may be assigned to the following input function buttons.
RECEIVER MULTI |
| SOURCE | |
| OPERATION |
| |
| RCU SETUP |
| |
|
| BDR |
|
BD | DVD | DVR | HDMI |
SAT |
|
|
|
TV | CD | HMG | ADPT |
USB |
|
| OPTION |
iPod | TUNER | SIRIUS |
|
INPUT SELECT | TV CTRL | RECEIVER | |
54En