Pioneer VSX-1121-K manual 55

Selecting preset codes directly

1Press and hold RCU SETUP, then press ‘1’ for three seconds.

Release the button after the LED flashes once. The LED continues to flash.

!To cancel the preset setup mode press

RCU SETUP.

2Press the input function button for the component you want to control.

When assigning preset codes to TV CONTROL, press TV CTRL here.

The LED blinks once and flashes continuously.

3Use the number buttons to enter the 4-digit preset code.

See Preset code list on page 93 .

If the LED lights for one second and continues to flash, the setting has been successfully completed.

When the preset code is fully input, the LED flashes three times to indicate that the setting has failed. If this happens, enter the 4-digit preset code again.

4Repeat steps 2 through 3 for the other components you want to control.

To try out the remote control, switch the com- ponent on or off (into standby) by pressing u SOURCE. If it doesn’t seem to work, select the next code from the list (if there is one).

5Press RCU SETUP to exit the preset setup mode.

Programming signals from other remote controls

If the preset code for your component is not available, or the available preset codes do not operate correctly, you can program signals from the remote control of another component. This can also be used to program additional operations (buttons not covered in the presets) after assigning a preset code.

Controlling the rest of your system

10

The remote can store about 120 preset codes

1 Press and hold RCU SETUP, then press

from other components (this has been tested

‘7’ for three seconds.

with codes of Pioneer format only).

3 cm

Release the button after the LED flashes once.

Certain buttons represent operations

that can-

(1 inch)

Other remote

The LED continues to flash.

This receiver’s

not be learned from other remote controls. The

! To cancel the preset setup mode press

remote control

control

buttons available are shown below:

RCU SETUP.

4 Press the corresponding button on

2 Press the input function button

AUDIO

VIDEO

RECEIVER MULTI

SOURCE

PARAMETER

PARAMETER

the other remote control that is sending

corresponding to the command to be

OPERATION

LIST

TUNE TOOLS

RCU SETUP

BAND

GUIDE

(teaching) the signal to this receiver’s

erased, then press ENTER.

TOP MENU

T.EDIT

BD

DVD

DVR

HDMI

remote control.

The LED flashes once.

BDR

PRESET

ENTER

PRESET

If the LED lights for one second and continues

SAT

3 Press and hold the button to be erased

TV

CD

HMG

ADPT

CATEGORY

RETURN

to flash, the setting has been successfully

for three seconds.

USB

OPTION

HOME

TUNE

completed.

iPod

TUNER

SIRIUS

MENU

If the LED lights for one second, the erasing has

INPUT SELECT

TV CTRL RECEIVER

iPod CTRL

! If the LED flashes for five seconds, it means

DIRECT

STEREO STANDARD ADV SURR

AUTO/ALC/ PGM

MEMORY MENU

the memory is full. See Erasing all learnt

been successfully completed.

HDD

DVD

MASTER

THX

PHASE

CTRL

STATUS

4 Repeat step 3 to erase other buttons.

INPUT

VOLUME

settings that are in one input function on

TV CONTROL

TV/DTV

MPX

PQLS

page 55 to erase a programmed button

5 Press RCU SETUP to exit the erasing

CH

VOL

HDMI OUT

AUDIO

you’re not using to free up more memory

mode.

MUTE

1

3

2

INFO

(note that some signals may take more

SIGNAL SEL MCACC

SLEEP

memory than others).

4

5

6

DISP

Erasing all learnt settings that

7

8

9

! Note that interference from TVs or other

CH LEVEL A.ATT

DIMMER

D.ACCESS

CLASS

CH

devices will sometimes result in the remote

are in one input function

/CLR

0

ENTER

control learning the wrong signal.

This operation erases all the operational

ZONE 2

ZONE 3

LIGHT

! Some commands from other remote controls

settings of other devices that have been pro-

cannot be learned, but in most cases the

grammed in one input function, and restores

1 Press and hold RCU SETUP, then press

remotes just need to be moved closer

the factory default.

together or farther apart.

‘2’ for three seconds.

This function is handy for erasing all data pro-

5 To program additional signals for the

Release the button after the LED flashes once.

grammed for devices no longer being used.

The LED continues to flash.

current component repeat steps 3 and 4.

1 Press and hold RCU SETUP, then press

! To cancel the preset setup mode press

To program signals for another component, exit

‘9’ for three seconds.

RCU SETUP.

and repeat steps 2 through 4.

Release the button after the LED flashes once.

2 Press the input function button for the

6 Press RCU SETUP to exit the

The LED continues to flash.

component you want to control.

programming mode.

! To cancel the preset setup mode press

The LED blinks once and flashes continuously.

RCU SETUP.

3 Point the two remote controls towards

2 Press and hold the input function

Erasing one of the remote

each other, then press the button that will

control button settings

button corresponding to the command to

be doing the learning on this receiver’s

be erased for three seconds.

remote control.

This erases one of the buttons you have pro-

If the LED lights for one second, the erasing has

The LED flashes once, then stops flashing,

grammed and restores the button to the factory

been successfully completed.

remaining lit.

default.

!The remote controls should be 3 cm (1 inch) apart.

En 55