Pioneer VSX1017TXV manual Additional information, Other audio problems, SymptomRemedy

Additional information 12

SymptomRemedy

No sound from surround back speakers.

•Check that the surround back speakers are set to LARGE or SMALL (see Speaker Setting on page 40).

•Make sure surround back processing is set to SBch ON (see Using surround back channel processing on page 30).

•If the source is Dolby Surround EX or DTS-ES with no flag to indicate 6.1 compatibility, then with surround back processing set to SBch Auto, there will be no sound from the surround back speakers. In this case, set to SBch ON (see Using surround back channel processing on page 30).

•If the source does not have 6.1 playback channels, make sure that surround back processing is set to SBch ON and a surround mode is selected (see Listening in surround sound on page 27).

•Check the speaker connections (see Connecting the speakers on page 18). If only one surround back speaker is connected, make sure it’s connected to the left channel speaker terminal.

No sound from subwoofer.	• Check that the subwoofer is connected properly, switched on and the volume turned up.
	• If your subwoofer has a sleep function, make sure it is switched off.
	• Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on page 40).
	• The crossover frequency may be set too low; try setting it higher to match the characteristics of your other
	speakers (see Speaker Setting on page 40)
	• If there is very little low frequency information in the source material, change your speaker settings to
	Front: SMALL / Subwoofer: YES, or Front: LARGE / Subwoofer: PLUS (see Speaker Setting on page 40).
	• Check the speaker level settings (see Channel Level on page 41).

No sound from one speaker.

•Check the speaker connection (see Connecting the speakers on page 18).

•Check the speaker level settings (see Channel Level on page 41).

•Check that the speaker hasn’t been set to NO (see Speaker Setting on page 40).

•The channel may not be recorded in the source. By using one of the advanced effect listening mode, you may be able to create the missing channel (see Listening in surround sound on page 27).

Sound is produced from analog	• Check that the input signal type is set to DIGITAL (see Choosing the input signal on page 30).
components, but not from digital	• Make sure that the digital input is assigned correctly for the input jack the component is connected to
ones (DVD, LD, CD-ROM etc.).	(see The Input Assign menu on page 52).
	• Check the digital output settings on the source component.
	• If the source component has a digital volume control, make sure this is not turned down.
	• Make sure that the multichannel analog inputs are not selected. Select any other input source.
No sound is output or a noise is	• Check that your DVD player is compatible with Dolby Digital/DTS discs.
output when Dolby Digital/DTS	• Check the digital output settings of your DVD player. Make sure that the DTS signal output is set to On.
software is played back.	• If the source component has a digital volume control, make sure this is not turned down.

Other audio problems

Symptom	Remedy
Broadcast stations cannot be	For FM broadcasts
selected automatically, or there is	• Fully extend the FM wire antenna, adjust the position for best reception and secure to a wall, etc.
considerable noise in radio	• Use an outdoor antenna for better reception (see page 21).
broadcasts.	For AM broadcasts
	• Adjust the position and direction of the AM antenna.
	• Use an outdoor antenna for better reception (see page 21).
	• Noise may be caused by interference from other equipment, such as a fluorescent light, motor, etc.
	Switch off or move the other equipment, or move the AM antenna.
A multichannel DVD source	• Make sure that the multichannel analog inputs are selected (see Selecting the multichannel analog inputs
appears to be downmixed to 2	on page 48).
channels during playback.

Noise is output when scanning a • This is not a malfunction of the receiver. The scan function of your player alters the digital information,

DTS CD.	making it unreadable, resulting in noise being output. Lower the volume when scanning.
When playing a DTS format LD	• Make sure that the input signal type is set to DIGITAL (see Choosing the input signal on page 30).
there is audible noise on the
soundtrack.
Can’t record audio.	• You can only make a digital recording from a digital source, and an analog recording from an analog
	source.
	• For digital sources, make sure that what you’re recording isn’t copy protected.
	• Check that the OUT jacks are properly connected to the recorders input jacks (see Connecting analog
	audio sources on page 17).

63

En