Planet Technology ERT-805 59

router rip

network 192.168.98.0 network 10.0.0.0

line vty 0 4 login

password 7 iFEdTlElgPbW4D

access-list 100 permit ip 192.168.98.0 0.0.0.255 192.168.99.0 0.0.0.255

end

Router 2 configuration

ERT-805#

router# show run

Building configuration ...

service password-encryption service timestamps debug

hostname router

enable password level 15 7 aNTUS0QSfz8T

crypto ipsec transform-set test esp-des

crypto map dynmap 1 ipsec-manual set transform-set test

set peer 10.0.0.2

set session-key inbound esp 256 cipher 0123456789ABCDEF set session-key outbound esp 256 cipher 1234567890ABCDEF match address 100

no crypto isakmp enable

interface fastethernet 0/0

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning Revision TABLE OF CONTENTS Page Chapter 1 Introduction 1.1 Checklist 1.2 About ERT-805 1.3 Product Feature 1.4 Product Specification Page Chapter 2 HARDWARE INSTALLATION 2.1 Package Contents 2.2 ERT-805outlook Rear Panel Warning 2.3 Installation requirements & Physical Installation 2.3.1 Device placement 2.3.2 Connect to a Ethernet device 2.3.3 Connect to a Serial Device 2.3.4 Power on the device Chapter 3 Command Line Interface 3.1 Help command 3.2 Redisplay Previous command 3.3 Verify Current Configuration 3.4 Ctrl-Z, Ctrl-Cand exit 3.5 Login from Console port 3.6 Virtual Terminal Access ERT805# config t ERT805(config)# enable password ERT805(config)#line vty 0 ERT805 ERT805(config-line)#password cisco 3.7 Password Encryption Page Chapter 4 Router Communication Protocol 4.1 RIP- Router Information Protocol 4.1.1 Routing loops 4.1.1.5 RIP Command Page 4.2 EIGRP – Enhanced interior Gateway Routing Protocol 4.2.1 EIRGP Command Page 4.3 OSPF- Open Shortest Path First 4.3.1 OSPF Command Page 4.4 PPP PPP authentication using PAP PPP authentication using CHAP CHAP example Page Page Page 4.5 HDLC Protocol Page 4.6 SNA 4.6.1 Introduction Page Page 4.7 X.25 Protocol encapsulation x25 [dce | dte] x25 address x25 map [Qllc] check-called-address check-calling-address x25 t21 x25 t22 x25 t23 x25 r20 x25 r22 – Access packet switching network s1:14.1.1.2/24 x121:14112 Router2 Router3 4.8 Frame Relay Protocol Page Page Page Chapter 5 Security 5.1 Access-list Page Page 5.2 NAT – Network Address Translation Page Page 5.3 VPN - IPSec Page crypto isakmp key address crypto isakmp policy -hash -encryption Page Page router# debug crypto isakmp router# 22:34.011 Crypto ISAKMP debugging is on router# term router# terminal m router# terminal monitor router# 23:03.993 IPSEC: SEND KEEYALIVE ON PEER 23:03.994 recv DPD req 23:03.994 creat a DPD struct Page Page Page Page Page Page Page Page Page Page 5.4 Firewall- Context-BasedAccess Control (CBAC) Page show ip inspect interface show ip inspect session debug ip inspect events debug ip inspect object-creation Page Page 5.5 Radius Security (AAA) Page Page Page Page Debug radius Chapter 6 QOS 6.1 CAR – Committed Access Rate Page Page 6.2 Policy-basedRouting 6.3 Class-mapand policy-map Page Page Page 6.4 Queue 6.4.1 FIFO- First IN First Out 6.4.2 WFQ – Weighted Fair Queuing 6.4.3 Priority Queuing Page Page 6.4.4 Custom Queuing queue number default queue limit byte-count Page Page Page Appendix A Upgrade firmware Input File Name Appendix B Router Dialing Page Appendix C Cables / Pin-assignmentfor ERT-805 C.1 V.35 DTE – CB-ERTV35-MT C.2 V.35 DCE – CB-ERTV35-FC C.3 V.24 DTE – CB-ERT232-MT C.4 V.24 DCE – CB-ERT232-FC C.5 X.21 DTE – CB-ERTX21-MT C.6 X.21 DCE – CB-ERTX21-FC C.7 RJ-45Console Cable C.8 DB9 to RJ45