Manuals / Brands / Computer Equipment / Switch / Planet Technology / Computer Equipment / Switch

Planet Technology FGSW-1828PS, FNSW-1608PS 3.2.1 Web Management, 3.1 Overview, 3.2 Management Method

1 72

Download 72 pages, 6.63 Mb

3. SWITCH MANAGEMENT

This chapter describes how to manage the Web Smart PoE Switch. Topics include:

-Overview

-Management method

-Logging on to the Web Smart PoE Switch

3.1 Overview

The Web Smart PoE Switch provides a user-friendly, Web interface. Using this interface, you can perform various switch configuration and management activities, including:

Please refer to the following Chapter 4 for the details.

3.2 Management Method

User can manage the Web Smart PoE Switch by Web Management via a network connection.

3.2.1 Web Management

The PLANET Web Smart PoE Switch provide a built-in browser interface. You can manage the Switch remotely by having a remote host with Web browser, such as Microsoft Internet Explorer, Netscape Navigator or Mozilla Firefox.

The following shows how to startup the Web Management of the Switch, please note the Web Smart PoE Switch is configured through an Ethernet connection, make sure the manager PC must be set on the same IP subnet address, for example, the default IP address of the Switch is 192.168.0.100 (the factory-default IP address), then the manager PC should be set at 192.168.0.x (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.

Use Internet Explorer 5.0 or above Web browser, enter default IP address http://192.168.0.100

After entering the username and password (default user name and password is “admin”) in login screen

- 11 -

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning WEEE Warning TABLE OF CONTENTS APPENDIX A NETWORKING CONNECTION 1.1 Checklist 1.2 About the Switch 1.3Features 1.4Specification PoE Power Output Power Pin Assignment Power Budget 2.1 Front Panel 2.1.1 LED indicators System Per 10/100Mbps port Per 10/100/1000Base-Tport / SFP interfaces (FGSW-1828PSonly) 2.2 Rear Panel Power Notice: 2.3 Hardware Installation 2.3.1 Desktop Installation 2.3.2 Rack Mounting Caution: 3.2.1 Web Management 3.2.2 PLANET Smart Discovery Utility 3.3Logging on to the FNSW-1608PS / FGSW-1828PS 4.1Login in to the Switch Page 4-2System Object Description 4.2.1 System Information 4.2.2 IP Configuration 4.2.3 Password Setting 4.2.4 Alert Trap 4.2.5 Factory Default 4.2.6 Firmware Update Page Page 4.2.7 Reboot 4-3Port Management 4.3.1 Port Configuration Page 4.3.2 Port Mirroring 4.3.3 Bandwidth Control 4.3.4 Broadcast Storm Control 4.3.5 Port Statistics 4-4VLAN Setting Page Page 4.4.1 802.1Q VLAN Page 802.1Q VLAN Setting example: Two separate 802.1Q VLAN scenario „Untagged packet entering VLAN „Tagged packet entering VLAN #Notice: Setup steps 1. Create VLAN Group: Page 3.Assign PVID for each port: 4.Enable VLAN Tag for specific ports Two separate 802.1Q VLAN with overlapping area scenario Page Page 4.4.2 Port Based VLAN Port Based VLAN Setting example: VLAN scenario 4.4.3 MTU VLAN 4-5Trunk Setting Page 4-6QoS Setting 4.6.1 Priority Mode 4.6.2 Class of Service Configuration 4.6.3 TCP / UDP Port Based QoS Page 4-7Security Filter 4.7.1 MAC Address Filter 4.7.2 TCP / UDP Filter Page 4-8Misc Operation 4-9POE Setting Power Management: Page 4-10Logout 5.1 Address Table 5.2 Learning 5.3 Forwarding & Filtering 5.4 Store-and-Forward 5.5 Auto-Negotiation „Mid-Span „End-Span PoE System Architecture How Power is Transferred Through the Cable Page Stages of powering up a PoE link Volts speci Volts man Stage Action 7.3 Start-up 7.4 Operation 7.5 Power Disconnection Scenarios DC Disconnect AC Disconnect The Link LED is not lit Some stations cannot talk to other stations located on the other port Performance is bad 100Base-TXport link LED is lit, but the traffic is irregular Why the Switch doesn’t connect to the network A.1 Switch‘s RJ-45Pin Assignments A.2 RJ-45cable pin assignment Straight Cable SIDE SIDE2 Figure A-1: Straight-Throughand Crossover Cable 2080-A31120-006 Taiwan 10th, JUNE