Planet Technology FGSW-1828PS, FNSW-1608PS 28

Figure 4-21Port Configuration Web Page Screen

Object		Description

Port		Allow choosing all or one port of Web Smart PoE Switch for further management, the
		available options is All & 01 to 16 (FNSW-1608PS). Or All & 01 to 18 (FGSW-1828PS).
Speed Mode		Allow choosing various speed duplex mode from one specific port of Web Smart PoE
		Switch , the available options are shown as below:
		Auto Negotiation
		1000Full (FGSW-1828PS 1000Mbps Port Only )
		100Full
		100Half
		10Full
		10Half
		Default mode is Auto Negotiation.
Flow Control		Allow to configure Flow control function of each port from Web Smart PoE Switch, the
		available options are Enable and Disable. Default mode is Enable.
State		Allow disable or enable one specific port from Web Smart PoE Switch, the available options
		are Enable and Disable. Default mode is Enable.
Port Description		Allow input per Port Description of Web Smart PoE Switch, up to maximum 8 characters
		allow.
Apply button		Press “Apply” button for save current configuration of each port on Web Smart PoE
		Switch.
	Table 4-4Descriptions of the Port Configuration Web Page Screen Objects

Object		Description

Port		Indicate port 1 to port 16 (FNSW-1608PS), port 1 to port 18 (FGSW-1828PS).

Current Status		Display per port Current Status, such as Link, Speed Mode and Flow Control.

Link		Display current link status from each port of the Web Smart PoE Switch.

Speed Mode		Display current speed mode from each port of the Web Smart PoE Switch.

Flow Control		Display current flow control status from each port of the Web Smart PoE Switch.


Setting Status		Display per port Current Setting Status, such as Speed Mode, Flow Control, State and Port
		Description.
Speed Mode		Display per port Speed Mode setting value.

Flow Control		Display per port Flow Control setting value.

State		Display per port State setting value.

Port Description		Display per Port Description.

Refresh button		Press “Refresh” button to refresh current status.

	Table 4-5Descriptions of the Port Configuration Web Page Screen Objects

- 28 -

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning WEEE Warning TABLE OF CONTENTS APPENDIX A NETWORKING CONNECTION 1.1 Checklist 1.2 About the Switch 1.3Features 1.4Specification PoE Power Output Power Pin Assignment Power Budget 2.1 Front Panel 2.1.1 LED indicators System Per 10/100Mbps port Per 10/100/1000Base-Tport / SFP interfaces (FGSW-1828PSonly) 2.2 Rear Panel Power Notice: 2.3 Hardware Installation 2.3.1 Desktop Installation 2.3.2 Rack Mounting Caution: 3.2.1 Web Management 3.2.2 PLANET Smart Discovery Utility 3.3Logging on to the FNSW-1608PS / FGSW-1828PS 4.1Login in to the Switch Page 4-2System Object Description 4.2.1 System Information 4.2.2 IP Configuration 4.2.3 Password Setting 4.2.4 Alert Trap 4.2.5 Factory Default 4.2.6 Firmware Update Page Page 4.2.7 Reboot 4-3Port Management 4.3.1 Port Configuration Page 4.3.2 Port Mirroring 4.3.3 Bandwidth Control 4.3.4 Broadcast Storm Control 4.3.5 Port Statistics 4-4VLAN Setting Page Page 4.4.1 802.1Q VLAN Page 802.1Q VLAN Setting example: Two separate 802.1Q VLAN scenario „Untagged packet entering VLAN „Tagged packet entering VLAN #Notice: Setup steps 1. Create VLAN Group: Page 3.Assign PVID for each port: 4.Enable VLAN Tag for specific ports Two separate 802.1Q VLAN with overlapping area scenario Page Page 4.4.2 Port Based VLAN Port Based VLAN Setting example: VLAN scenario 4.4.3 MTU VLAN 4-5Trunk Setting Page 4-6QoS Setting 4.6.1 Priority Mode 4.6.2 Class of Service Configuration 4.6.3 TCP / UDP Port Based QoS Page 4-7Security Filter 4.7.1 MAC Address Filter 4.7.2 TCP / UDP Filter Page 4-8Misc Operation 4-9POE Setting Power Management: Page 4-10Logout 5.1 Address Table 5.2 Learning 5.3 Forwarding & Filtering 5.4 Store-and-Forward 5.5 Auto-Negotiation „Mid-Span „End-Span PoE System Architecture How Power is Transferred Through the Cable Page Stages of powering up a PoE link Volts speci Volts man Stage Action 7.3 Start-up 7.4 Operation 7.5 Power Disconnection Scenarios DC Disconnect AC Disconnect The Link LED is not lit Some stations cannot talk to other stations located on the other port Performance is bad 100Base-TXport link LED is lit, but the traffic is irregular Why the Switch doesn’t connect to the network A.1 Switch‘s RJ-45Pin Assignments A.2 RJ-45cable pin assignment Straight Cable SIDE SIDE2 Figure A-1: Straight-Throughand Crossover Cable 2080-A31120-006 Taiwan 10th, JUNE