Manuals / Brands / Computer Equipment / Switch / Planet Technology / Computer Equipment / Switch

Planet Technology FGSW-1828PS, FNSW-1608PS 3.Assign PVID for each port:, 4.Enable VLAN Tag for specific ports

1 72

Download 72 pages, 6.63 Mb

	#Notice:	Its import to remove the VLAN member port from VLAN 1 group. Or the ports would become overlap-
	#Notice:	ping setting.
		ping setting.

3.Assign PVID for each port:

Port-1,Port-2 and Port-3 : PVID=2.

Port-4,Port-5 and Port-6 : PVID=3.

Port-7~Port-18: PVID=1.

4.Enable VLAN Tag for specific ports

Link Type: Port-3 (VLAN-2) and Port-6 (VLAN-3).

The Per Port VLAN configuration in Figure 4-34 appears.

Figure 4-34Port 1-Port 6 802.1Q VLAN Configuration

- 41 -

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning WEEE Warning TABLE OF CONTENTS APPENDIX A NETWORKING CONNECTION 1.1 Checklist 1.2 About the Switch 1.3Features 1.4Specification PoE Power Output Power Pin Assignment Power Budget 2.1 Front Panel 2.1.1 LED indicators System Per 10/100Mbps port Per 10/100/1000Base-Tport / SFP interfaces (FGSW-1828PSonly) 2.2 Rear Panel Power Notice: 2.3 Hardware Installation 2.3.1 Desktop Installation 2.3.2 Rack Mounting Caution: 3.2.1 Web Management 3.2.2 PLANET Smart Discovery Utility 3.3Logging on to the FNSW-1608PS / FGSW-1828PS 4.1Login in to the Switch Page 4-2System Object Description 4.2.1 System Information 4.2.2 IP Configuration 4.2.3 Password Setting 4.2.4 Alert Trap 4.2.5 Factory Default 4.2.6 Firmware Update Page Page 4.2.7 Reboot 4-3Port Management 4.3.1 Port Configuration Page 4.3.2 Port Mirroring 4.3.3 Bandwidth Control 4.3.4 Broadcast Storm Control 4.3.5 Port Statistics 4-4VLAN Setting Page Page 4.4.1 802.1Q VLAN Page 802.1Q VLAN Setting example: Two separate 802.1Q VLAN scenario „Untagged packet entering VLAN „Tagged packet entering VLAN #Notice: Setup steps 1. Create VLAN Group: Page 3.Assign PVID for each port: 4.Enable VLAN Tag for specific ports Two separate 802.1Q VLAN with overlapping area scenario Page Page 4.4.2 Port Based VLAN Port Based VLAN Setting example: VLAN scenario 4.4.3 MTU VLAN 4-5Trunk Setting Page 4-6QoS Setting 4.6.1 Priority Mode 4.6.2 Class of Service Configuration 4.6.3 TCP / UDP Port Based QoS Page 4-7Security Filter 4.7.1 MAC Address Filter 4.7.2 TCP / UDP Filter Page 4-8Misc Operation 4-9POE Setting Power Management: Page 4-10Logout 5.1 Address Table 5.2 Learning 5.3 Forwarding & Filtering 5.4 Store-and-Forward 5.5 Auto-Negotiation „Mid-Span „End-Span PoE System Architecture How Power is Transferred Through the Cable Page Stages of powering up a PoE link Volts speci Volts man Stage Action 7.3 Start-up 7.4 Operation 7.5 Power Disconnection Scenarios DC Disconnect AC Disconnect The Link LED is not lit Some stations cannot talk to other stations located on the other port Performance is bad 100Base-TXport link LED is lit, but the traffic is irregular Why the Switch doesn’t connect to the network A.1 Switch‘s RJ-45Pin Assignments A.2 RJ-45cable pin assignment Straight Cable SIDE SIDE2 Figure A-1: Straight-Throughand Crossover Cable 2080-A31120-006 Taiwan 10th, JUNE