Manuals / Brands / Computer Equipment / Switch / Planet Technology / Computer Equipment / Switch

Planet Technology GSW-2416SF 4.5 Firmware Update, Firmware update requirements, Update procedure:, update, Figure, GSW-2416SF>”

1 54

Download 54 pages, 2.33 Mb

4.5 Firmware Update

This section will show you how to use X-modem to update the firmware of GSW-2416SF.

Firmware update requirements

GSW-2416SF switch

Latest firmware version

VT100 terminal, or a personal computer or workstation with terminal emulation software

RS-232/DB9 null modem cable

Update procedure:

1.After login the GSW-2416SF, enter “update” in the”GSW-2416SF>”prompt. Then the message will ask you to use the Xmodem to send the firmware file. The firmware update screen in Figure 4-33appears:

Figure 4-33Firmware Update

2.Select and send the firmware file by your terminal emulation software. As the screens show in Figure 4-34and Figure

4-35:

#Notice:

1.Make sure that you had selected the correct firmware file that just for the GSW-2416SF and read the release note before you run the update procedure.

2.Don’t power off the switch while updating firmware or unexpected result occurred.

EM-GSW2416SFv1

- 33 -

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning WEEE Warning TABLE OF CONTENTS 1. INTRODUCTION 1.1 Checklist 1.2 About the Switch 1.3Features 1.4Specification 2. HARDWARE DESCRIPTION 2.1 Front Panel 2.1.1 LED indicators System Per 10/100/1000Mbps port 2.3 Hardware Installation 2.3.1 Desktop Installation 2.3.2 Rack Mounting Caution: 3. SWITCH MANAGEMENT 3.1 Overview 3.2 Management Methods 3.2.1 Local Console Management 3.2.2 Web Management 3.3 Assigning an IP Address to the Switch 3.4 Logging on to the GSW-2416SF 4. CONSOLE INTERFACE 4.1 CONNECT TO PC RS-232serial cable Hyper Terminal 4.2 Login in 4.3 Main Menu screen 4.4 Getting Started 4.4.1 General Guidelines 4.4.2 Show command 4.4.2.1 Show port 4.2.2.2 Show static [n] 4.4.2.3Show vlan [n] 4.4.2.4 Show ip 4.4.2.5 Show version 4.4.2.6 Show flowcontrol 4.4.2.7 Show vlantag 4.4.2.8 Show vlanaware 4.4.2.9 Show priority 4.4.2.10 Show pvid 4.4.2.11 Show vid 4.4.3Set command 4.4.3.1 Set port [n] Description 4.4.3.2 Set vlan [n] 4.4.3.3 Set flowcontrol Set flowcontrol [n] enable/disable 4.4.3.4 Set vlantag Set vlantag [n] enable/disable 4.4.3.5 Set vlanaware Set vlanaware [n] enable/disable 4.4.3.6 Set priority Set priority [n] [m] 4.4.3.7 Set pvid Set pvid [n] [m] 4.4.3.8 Set vid Set vid [n] [m] 4.4.3.9 Set ip xxx.xxx.xxx.xxx.mmm.mmm.mmm.mmm.ggg.ggg.ggg.ggg IP: Netmask: Default Gateway: 4.4.3.10 Set pass 4.4.4 Factory default 4.4.5 Reboot 4.4.6 Logout 4.5 Firmware Update Firmware update requirements Update procedure: Page 5. WEB MANAGEMENT 5.1 Login in to the Switch 5.2 Port Config Object 5.3 VLAN Setup 5.3.1 VLAN Group and member settings 5.3.2 VLAN setting example: 5.3.2.1 Two separate VLAN Setup steps 1.VLAN Group 2.Assign VLAN Member : 3.Assign PVID for each port: 4.Enable VLAN Tag for specific ports Page 5.3.2.2 Overlap VLAN Setup steps 1.Port Setting 2.PVID setup 5.4 Port Trunk Setup Member Page 5.5 Status 5.5.1 Port Status 5.5.2 Statistics Clear Refresh 5.6 Misc Configuration 5.6.1 System Setup 5.7 Tools 5.7.1 Reboot 5.7.2 Factory Reset 5.8 Logout 6. SWITCH OPERATION 6.1 Address Table 6.2 Learning 6.3 Forwarding & Filtering 6.4 Store-and-Forward 7.TROUBLESHOOTING The Link LED is not lit Some stations cannot talk to other stations located on the other port Performance is bad 100Base-TXport link LED is lit, but the traffic is irregular APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45Pin Assignments 10/100Base-TX A.1 Switch‘s RJ-45 Pin Assignments Figure A-1: Straight-Throughand Crossover Cable