Manuals / Brands / Computer Equipment / Switch / Planet Technology / Computer Equipment / Switch

Planet Technology GSW-2416SF 4. CONSOLE INTERFACE, 4.1 CONNECT TO PC, RS-232serial cable, Hyper Terminal, None, None, Figure, “HyperTerminal”, ƒEmulation: VT-100compatible

1 54

Download 54 pages, 2.33 Mb

4. CONSOLE INTERFACE

4.1 CONNECT TO PC

RS-232 serial cable

Use the bundled RS-232 serial cable and attach the 9-pin female connector to the male connector on the GSW-2416SF. Plug the other side of this cable to your PC.

Hyper Terminal

In Windows 98/2000/ME/XP, launch “HyperTerminal”, create a new connection, and adjust settings as below:

Emulation: VT-100 compatible

Baud per second: 19200

Data bits: 8

Parity: None

Stop bits: 1

Flow Control: None

To gain a demo, please see the Figure 4-1.

Figure 4-1Port Settings for console interface

EM-GSW2416SFv1

- 12 -

Contents

Page Trademarks Disclaimer FCC Warning CE Mark Warning WEEE Warning TABLE OF CONTENTS 1. INTRODUCTION 1.1 Checklist 1.2 About the Switch 1.3Features 1.4Specification 2. HARDWARE DESCRIPTION 2.1 Front Panel 2.1.1 LED indicators System Per 10/100/1000Mbps port 2.3 Hardware Installation 2.3.1 Desktop Installation 2.3.2 Rack Mounting Caution: 3. SWITCH MANAGEMENT 3.1 Overview 3.2 Management Methods 3.2.1 Local Console Management 3.2.2 Web Management 3.3 Assigning an IP Address to the Switch 3.4 Logging on to the GSW-2416SF 4. CONSOLE INTERFACE 4.1 CONNECT TO PC RS-232serial cable Hyper Terminal 4.2 Login in 4.3 Main Menu screen 4.4 Getting Started 4.4.1 General Guidelines 4.4.2 Show command 4.4.2.1 Show port 4.2.2.2 Show static [n] 4.4.2.3Show vlan [n] 4.4.2.4 Show ip 4.4.2.5 Show version 4.4.2.6 Show flowcontrol 4.4.2.7 Show vlantag 4.4.2.8 Show vlanaware 4.4.2.9 Show priority 4.4.2.10 Show pvid 4.4.2.11 Show vid 4.4.3Set command 4.4.3.1 Set port [n] Description 4.4.3.2 Set vlan [n] 4.4.3.3 Set flowcontrol Set flowcontrol [n] enable/disable 4.4.3.4 Set vlantag Set vlantag [n] enable/disable 4.4.3.5 Set vlanaware Set vlanaware [n] enable/disable 4.4.3.6 Set priority Set priority [n] [m] 4.4.3.7 Set pvid Set pvid [n] [m] 4.4.3.8 Set vid Set vid [n] [m] 4.4.3.9 Set ip xxx.xxx.xxx.xxx.mmm.mmm.mmm.mmm.ggg.ggg.ggg.ggg IP: Netmask: Default Gateway: 4.4.3.10 Set pass 4.4.4 Factory default 4.4.5 Reboot 4.4.6 Logout 4.5 Firmware Update Firmware update requirements Update procedure: Page 5. WEB MANAGEMENT 5.1 Login in to the Switch 5.2 Port Config Object 5.3 VLAN Setup 5.3.1 VLAN Group and member settings 5.3.2 VLAN setting example: 5.3.2.1 Two separate VLAN Setup steps 1.VLAN Group 2.Assign VLAN Member : 3.Assign PVID for each port: 4.Enable VLAN Tag for specific ports Page 5.3.2.2 Overlap VLAN Setup steps 1.Port Setting 2.PVID setup 5.4 Port Trunk Setup Member Page 5.5 Status 5.5.1 Port Status 5.5.2 Statistics Clear Refresh 5.6 Misc Configuration 5.6.1 System Setup 5.7 Tools 5.7.1 Reboot 5.7.2 Factory Reset 5.8 Logout 6. SWITCH OPERATION 6.1 Address Table 6.2 Learning 6.3 Forwarding & Filtering 6.4 Store-and-Forward 7.TROUBLESHOOTING The Link LED is not lit Some stations cannot talk to other stations located on the other port Performance is bad 100Base-TXport link LED is lit, but the traffic is irregular APPENDIX A NETWORKING CONNECTION A.1 Switch‘s RJ-45Pin Assignments 10/100Base-TX A.1 Switch‘s RJ-45 Pin Assignments Figure A-1: Straight-Throughand Crossover Cable

4. CONSOLE INTERFACE

4.1 CONNECT TO PC

RS-232 serial cable

Hyper Terminal

Emulation: VT-100 compatible

Emulation: VT-100 compatible