Manuals / Plus / Computer Equipment / Projector

Plus UP-1100 user manual Status Light Messages, STATUS indicator, Condition

Models: UP-1100

1 34

Download 34 pages 39.44 Kb

Page 31

Status Light Messages

W h e n t h e S T A T U S i n d i c a t o r l i g h t s o r b l i n k s

STATUS POWER

STATUS indicator

MENU SELECT ENTER

ADJUST

Status Light Messages

Condition	Status

OFF	Normal

On Continually	The projector lamp has exceeded 1000 hours of operation and should be replaced.

Blinking Very Rapidly (On and off	•	The lamp housing is not correctly installed. Install it correctly.
in a cycle of 1 sec.)

Blinking Rapidly	•	The temperature protector has been triggered. If the room temperature is high,
(On and off in a cycle of 4 sec.)		move the projector to a cool location. If the temperature within the projector is
		high, check the cooling fan ventilation hole and the ventilation hole on the bottom
		of the projector. If any of the holes are blocked, remove whatever is blocking them.
	•	The temperature protector has been triggered. If you switch the main Power switch
		Off, then immediately switch it On again, sometimes the power does not come on. If
		this happens, wait one minute, then switch the power On again.
	•	The lamp lighting voltage error detection protector has been triggered. Wait at
		least one minute before switching it on again. If this does not solve the problem,
		please contact your dealer.

Blinking Slowly (On and off in a	The cooling fan has stopped. Contact your PLUS dealer for service.
cycle of 8 sec.)

Blinking Very Slowly (On and off in	The lamp is not turned on.
a cycle of 12 sec.)	•	The projector was turned off and back on too quickly. Turn off the projector, wait
		one minute, then turn the projector back on. Or the lamp is burnt out.

E – 31

Image 31

Plus UP-1100 user manual Status Light Messages, STATUS indicator, Condition

Contents

PLUS UP-1100 EnglishUSER’S MANUAL RF Interference PrecautionsImportant Safeguards I M P O R T A N T S A F E T Y I N F O R M A T I O NOperation T a b l e o f c o n t e n t sBasic information and preparations ConnectionsFor remote control A b o u t y o u r U P - 1 1 0C h e c k i n g t h e s u p p l i e d The features you’ll enjoyInserting the batteries Remote control effective rangea c c e s s o r i e s P r e p a r i n g t h e r e m o t e c o n t r o lADJUST +/- button P a r t s a n d c o n t r o l sFront and side panel view STATUS indicatorHandle Rear adjuster AC IN terminal Built-in security slot see below Rear and side panel viewBottom Built-in Security SlotPLUS P a r t s a n d c o n t r o l s c o n t i n u e d Remote controlPOWER ON button 16 VOLUME +/- buttonScreen I n s t a l l a t i o nPositioning the unit Projecting distance and image sizeProjection distance Using the ceiling mounting fixturesI n s t a l l a t i o n c o n t i n u e d Diagonal image size inchBefore connecting Connecting to the VIDEO IN VIDEO/S- VIDEO jacksC o n n e c t i n g v i d e o e q u i p m e n t Before connectingMacintosh desktop computer C o n n e c t i n g a P C o r M a c i n t o s hRESOLUTION Modifying the DIP switch for Macintosh settingNote on the PowerBook connection DIP switch setting = ONa s a c o m p u t e r f u n c t i o n Connecting the remote mouse receiver to an IBM PC/AT computerU s i n g t h e r e m o t e m o u s e - W i r e l e s s c o n t r o l m o u s eThe unit terminal panel A d d i t i o n a l c o n n e c t i o n sComputer or video equipment Speaker with an amplifier Monitor4 Press either VIDEO, S-VIDEO, or RGB to select the input source 5 Adjust the position and height of the unitU s i n g t h e D a t a P r o j e c t o r 3 Turn on the connected source computer, VCR, DVD player, etcOperating with the unit 1 Press the POWER button After using the Data Projector8 Adjust the picture elements and select the picture type 9 Start using the Data ProjectorWindows Changing computer’s video resolutionsNotebook computers and resolution standards U s i n g t h e D a t a P r o j e c t o r c o n t i n u e dTurning off the image and muting the sound temporarily Adjusting the volume of the unit speakerUsing the laser pointer Press VOLUME + to increase the volume or - to decrease1 Press POSITION V a r i o u s f u n c t i o n s w h i l e u s i n g c o n t i n u e dt h e D a t a P r o j e c t o r Enlarging the picture6 Press R-CLICK to turn off the menu dis- play Operating with the unit1 Press MENU 5 Press L-CLICKWhen the input source is VIDEO or S-VIDEO M e n u s t r u c t u r eWhen the input source is RGB and “INPUT MODE” is “RGB” When the input source is RGB and “INPUT MODE” is “YCbCr” When the input source is RGB and “INPUT MODE” is “YCbCr”When the input source When the input sourceS e t t i n g “ I N P U T M O D E ” t o “ Y C b C r ” S e l e c t i n g t h e p r o j e c t i o n t y p eS e l e c t i n g a d i s p l a y l a n g u a g e S e l e c t i n g t h e b a c k g r o u n dc o n n e c t e d t o Timing ChartA d j u s t i n g t h e i m a g e f r o mt h e R G B I N c o n n e c t o r c o n t i n u e d A d j u s t i n g t h e p i c t u r e e l e m e n t s Resetting the present settings to factory settingsSelecting the starting mode for the next use of the unit S e l e c t i n g t h e w i d e s c r e e n d i s p l a y S e l e c t i n g t h e p i c t u r e t y p eA c t i v a t i n g t h e p o w e r s a v i n g f u n c t i o n Q u i c k s t a r t i n g t h e u n i tR e s e t t i n g a l l t o t h e f a c t o r y s e t t i n g s Resetting the lamp use hours to zeroA c t i v a t i n g t h e o n - s c r e e n f u n c t i o n C h e c k i n g h o u r s o f l a m p u s eO t h e r s T r o u b l e s h o o t i n gCommon Problems & Solutions ProblemStatus Status Light MessagesSTATUS indicator ConditionStep Lamp housing replacement procedureR e p l a c i n g t h e l a m p h o u s i n g StepMechanical S p e c i f i c a t i o n sOptical ElectricalDimensions S p e c i f i c a t i o n s c o n t i n u e d D-Sub Pin AssignmentsPC 15-Pin mini D-Sub