Pro-Tech ULV Celeron M 3.5 Embedded Card With VGA/ SOUND/ LAN

Chapter 2 Hardware Configuration

2-5. RS232/422/485 (COM2) SELECTION

JP1 : RS-232/422/485 (COM2) Selection

This connector is used to set the COM2 function.

The jumper settings are as follows :

COM 2	Jumper Settings	Jumper
Function	(pin closed)	Illustrations

RS-232	Open

RS-422	1-2, 3-4, 9-10

RS-485	1-2, 5-6, 7-8

*** Manufactory default --- RS-232.

EB-471LF USER′S MANUAL

Page: 2-7

Image 17

Pro-Tech ULV Celeron M 3.5 Embedded Card With VGA/ SOUND/ LAN, EB-471LF M1 user manual RS232/422/485 COM2 Selection

Contents

USER’S Manual EB-471LF Celeron M FCC Notice Table of Contents Appendix Expansion BUS Introduction About this Manual Hardware Configuration CPU System Specification Display Safety Precautions Hardware Jumper & Connector Quick Reference Table Component Locations EB-471LF Connector, Jumper and Component locations Jumpers and Caps HOW to SET the Jumpers Jumper Settings Jumper Diagrams RS-232 RS-422 RS-485 COM Port Connector RS232/422/485 COM2 Selection Jumper Settings Function Pin closed Illustrations Reset Connector KEYBOARD/MOUSE ConnectorHard Disk Drive LED Connector JPANEL1 7,8 Reset Connector Irda Connector External Speaker ConnectorPower LED Connector VGA Connector System FAN Connector PIN Assignment Hard Disk Drive Connector LAN Connector Universal Serial BUS Connector Clear Cmos Data Selection Function Jumper Setting Settings Power Requirement Selection Inverter Connector AT Power Connector Illustration RESET/NMI Watchdog Selection Lvds Connector Panel Voltage Selection TV-OUT Connector Sound Connector LAN LED Software Utilities Filename Purpose Assume that CD ROM drive is D IntroductionVGA Driver Utility Installation of VGA Driver To update VGA Bios for LCD Flat Panel Display Flash Bios UpdateSystem Bios Update Page3-5 Introduction LAN Driver Utility Sound Driver Utility Installation Procedure for Windows 9x/NT/2000/XP Installation of Utility for Windows 98SE/ME/2000/XP Intel Chipset Software Installation Utility Installation of Utility for Windows 98SE/ 2000/XP USB2.0 Software Installation Utility Configuration Sequence Watchdog Timer Configuration Page3-11 Award Bios Setup Introduction Setup program initial screen Entering Setup Cmos Setup screen Standard Cmos Features IDE Primary Master / Slave IDE Secondary Master / Slave Video Drive a and Drive BHalt on Base Memory Award Hard Disk Type Table Hard Disk Attributes Bios Features Setup Screen Advanced Bios FeaturesQuick Power on SELF-TEST CPU L1 & L2 Cache Boot UP Numlock Status FIRST/SECOND/ Boot DeviceTypematic Rate Setting Typematic Delay Msec Chipset Features Setup Screen Advanced Chipset Features Dram RAS# to CAS# Delay Active to Precharge DelayDram Data Integrity Mode System Bios Cacheable Memory Hole AT 15M-16M Delayed TransactionAGP Aperture Size ON-CHIP VGA Integrated Peripherals Integrated Peripherals Setup Screen OnChip Primary PCI IDE Onchip IDE DevicePrimary Master/Slave PIO Secondary Master/Slave PIO Primary Master/Slave Udma Secondary Master/Slave Udma USB Controller Onboard DeviceUSB Keyboard Support USB Mouse Support Super IO Device Power Management Setup Screen Power Management SetupPower Management Modem USE IRQ Reset Configuration Data PNP/PCI ConfigurationPNP/PCI Configuration Setup Screen IRQ-n Assigned to Resource Controlled byIRQ Resources Current CPU Temperature Current Warning TemperaturePC Health Status Current System FAN Speed Frequency Control Frequency Control Setup ScreenAuto Detect PCI CLK Spread Spectrum Load Optimized Defaults Load FAIL-SAFE Defaults To Disable the Password SET Supervisor PASSWORD/SET User PasswordTo SET a Password Save & Exit Setup Exit Without Saving Expansion BUS PC/104 Plus BUS Connector PIN Assignment Technical Summary Block Diagram IRQ Assignment Interrupt MAP Code Assignment RTC & Cmos RAM MAP DMA Channel Map Assignment Timer & DMA Channels MAPTimer Channel Map Assignment Map Memory MAPMemory Map