Panel Voltage Selection | Pro-Tech EB-471LF M1 specs

Chapter 2 Hardware Configuration

2-23. PANEL VOLTAGE SELECTION

JP5 : Panel Voltage Selection.

The selections are as follows:

SELECTION

JUMPER SETTING

LVDS_VCC3

1-3, 2-4

LVDS_VCC5

3-5, 4-6

JUMPER

ILLUSTRATION

Page: 2-18

EB-471LF USER′S MANUAL

Image 28

Pro-Tech EB-471LF M1, ULV Celeron M 3.5 Embedded Card With VGA/ SOUND/ LAN user manual Panel Voltage Selection

Contents

USER’S Manual EB-471LF Celeron M FCC Notice Table of Contents Appendix Expansion BUS Introduction Hardware Configuration About this Manual System Specification CPU Display Safety Precautions Hardware Jumper & Connector Quick Reference Table EB-471LF Connector, Jumper and Component locations Component Locations HOW to SET the Jumpers Jumpers and Caps Jumper Diagrams Jumper Settings COM Port Connector RS-232 RS-422 RS-485 Jumper Settings Function Pin closed Illustrations RS232/422/485 COM2 Selection KEYBOARD/MOUSE Connector Reset ConnectorHard Disk Drive LED Connector JPANEL1 7,8 Reset Connector Power LED Connector External Speaker ConnectorIrda Connector System FAN Connector VGA Connector Hard Disk Drive Connector PIN Assignment Universal Serial BUS Connector LAN Connector Function Jumper Setting Clear Cmos Data Selection Power Requirement Selection Settings AT Power Connector Inverter Connector RESET/NMI Watchdog Selection Illustration Lvds Connector Panel Voltage Selection Sound Connector TV-OUT Connector LAN LED Software Utilities VGA Driver Utility IntroductionFilename Purpose Assume that CD ROM drive is D Installation of VGA Driver System Bios Update Flash Bios UpdateTo update VGA Bios for LCD Flat Panel Display Page3-5 LAN Driver Utility Introduction Installation Procedure for Windows 9x/NT/2000/XP Sound Driver Utility Intel Chipset Software Installation Utility Installation of Utility for Windows 98SE/ME/2000/XP USB2.0 Software Installation Utility Installation of Utility for Windows 98SE/ 2000/XP Watchdog Timer Configuration Configuration Sequence Page3-11 Award Bios Setup Introduction Entering Setup Setup program initial screen Standard Cmos Features Cmos Setup screen IDE Primary Master / Slave IDE Secondary Master / Slave Drive a and Drive B VideoHalt on Base Memory Hard Disk Attributes Award Hard Disk Type Table Advanced Bios Features Bios Features Setup ScreenQuick Power on SELF-TEST CPU L1 & L2 Cache FIRST/SECOND/ Boot Device Boot UP Numlock StatusTypematic Rate Setting Typematic Delay Msec Advanced Chipset Features Chipset Features Setup Screen Active to Precharge Delay Dram RAS# to CAS# DelayDram Data Integrity Mode System Bios Cacheable Delayed Transaction Memory Hole AT 15M-16MAGP Aperture Size ON-CHIP VGA Integrated Peripherals Setup Screen Integrated Peripherals Onchip IDE Device OnChip Primary PCI IDEPrimary Master/Slave PIO Secondary Master/Slave PIO Primary Master/Slave Udma Secondary Master/Slave Udma Onboard Device USB ControllerUSB Keyboard Support USB Mouse Support Super IO Device Power Management Setup Power Management Setup ScreenPower Management Modem USE IRQ PNP/PCI Configuration Setup Screen PNP/PCI ConfigurationReset Configuration Data IRQ Resources Resource Controlled byIRQ-n Assigned to Current Warning Temperature Current CPU TemperaturePC Health Status Current System FAN Speed Frequency Control Setup Screen Frequency ControlAuto Detect PCI CLK Spread Spectrum Load FAIL-SAFE Defaults Load Optimized Defaults To SET a Password SET Supervisor PASSWORD/SET User PasswordTo Disable the Password Save & Exit Setup Exit Without Saving Expansion BUS PC/104 Plus BUS Connector PIN Assignment Technical Summary Block Diagram Interrupt MAP IRQ Assignment RTC & Cmos RAM MAP Code Assignment Timer Channel Map Assignment Timer & DMA Channels MAPDMA Channel Map Assignment Memory Map Memory MAPMap