TROUBLE-SHOOTING

Most problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time.

1.SYMPTOM: THE SPA WILL NOT OPERATE

a.Check to see if the GFCI breaker is tripped, or was not turned on. Reset the GFCI breaker.

2.SYMPTOM: THE CIRCUIT BREAKER OR THE GFCI TRIPS WHILE THE SPA IS OPERATING

a.Reset the circuit breaker or the GFCI. If the cir- cuit breaker or the GFCI trips again, contact a qualified electrician for service.

3.SYMPTOM: THE PUMP HUMS

a.The filter may be dirty or damaged. Remove the filter housing from the spa jet unit and clean or replace the filter.

b.The pump may have a foreign object stuck in the impeller. Contact our customer service department.

c.The pump may have a loose wire connection. Contact our customer service department.

4.SYMPTOM: THE PUMP HUMS BUT DOES NOT ROTATE

a.The pump may be jammed. Contact our cus- tomer service department or, if your spa is no longer under warranty, you may also contact a local spa and pool service provider.

5.SYMPTOM: THE PUMP IS NOISY WHILE OPERATING

a.There may be debris in the pump. Contact our customer service department.

b.The pump may have a bad bearing. Contact our customer service department.

6.SYMPTOM: THE WATER DOES NOT HEAT

a.Make sure that the hydrotherapy spa is fully covered with the spa cover. The spa cover must be tight for the water to heat. Set the air control to low. Set the temperature to the desired setting. The water will heat at 6.0 to 8.0¡F an hour. If you are using the spa indoors,

and the room temperature is maintained at 70¡F, it will take approximately 5 to 7 hours for the water to reach the set temperature.

b. If you are using the HYDROTHERAPY SPA outdoors, it may take longer for the water to heat. See the chart below for the approximate heating time.

Air Temperature

Heating Time

70¡F +

5 to 7 hours

50¡FÐ70¡F

7 to 10 hours

30¡FÐ50¡F

10 to 15 hours

b. If the water still has not heated after four days, contact our customer service department.

c. If actual water temperature is lower that the set temperature, and the Heat On LED indicator on the console is not lit, contact our customer ser- vice department.

7.SYMPTOM: THE WATER IS NOT BEING CLEANED BY THE FILTER

a.Check to see if the filter is in place. Clean the filter if it is dirty.

b.Check the chemical balance of the water. If the pH is incorrect, the sanitizing agents will not function properly.

8.SYMPTOM: THE WATER PULSATES OR THERE IS MINIMUM WATER FLOW

a.Adjust the water level. This usually occurs only when the water level is low. Add water until the thera-jets are covered (see step 5 on page 9).

9.SYMPTOM: THE WATER LEVEL DROPS

a.Some water loss due to evaporation is normal. If rapid water loss occurs, or if you notice wet- ness on the floor around the hydrotherapy spa, then the spa shell may have a leak. Contact your local spa and pool service provider for repairs.

b.A clamp or seal inside the pump compartment may be loose. Check inside the pump compart-

20

Page 19 Page 21
Page 20
Image 20
ProForm 831.21005 user manual Trouble-Shooting
Page 19 Page 21

831.21005 specifications

The ProForm 831.21005 is an advanced treadmill designed for home fitness enthusiasts seeking an effective and convenient way to achieve their health goals. This model combines innovative technology with user-friendly features, making it an excellent addition to any home gym setup.

One of the standout features of the ProForm 831.21005 is its robust motor. With a powerful 2.75 HP motor, this treadmill delivers a smooth and consistent performance, supporting users through various workout intensities. The motor is designed to handle high speeds, allowing for a top speed of 10 MPH. This versatility accommodates both walking and running workouts, catering to a wide range of fitness levels.

Another key characteristic of the ProForm 831.21005 is its adjustable incline functionality. Users can simulate outdoor running conditions by adjusting the incline to different levels, enhancing calorie burn and engaging various muscle groups. This feature not only adds variety to workouts but also allows for a more challenging experience.

The treadmill boasts a spacious running surface, measuring 18 inches in width and 55 inches in length. This ample space grants users freedom of movement, thereby making workouts more comfortable and enjoyable. The ProForm 831.21005 is also equipped with ProForm's ComfortTech cushioning system, which reduces impact on joints and provides a more comfortable run, minimizing the risk of injury during long sessions.

In terms of technology, the ProForm 831.21005 is designed with an easy-to-read LCD display that tracks essential workout metrics, including speed, time, distance, and calories burned. Additionally, it features built-in workout programs that allow users to explore different routines, encouraging goal achievement and promoting weight loss.

Moreover, the treadmill is compatible with iFit technology, providing access to a library of interactive workouts led by professional trainers. With iFit, users can explore new terrains and participate in global workouts, making home exercise more engaging and dynamic.

Durability is another noteworthy attribute of the ProForm 831.21005. Its sturdy frame is designed to withstand regular use, ensuring longevity and reliability. The portable design allows for easy storage, making it a practical choice for those with limited space.

In conclusion, the ProForm 831.21005 is a feature-rich treadmill that combines performance, technology, and user comfort. Its powerful motor, adjustable incline, cushioning system, and compatibility with iFit technology make it a strong contender for anyone serious about improving their fitness from home.
Top Page Image Contents