Manuals / ProForm / Fitness & Sports / Treadmill

ProForm PFTL06009.0 user manual PROBLEM The incline of the treadmill does not change correctly

Models: PFTL06009.0

1 32

Download 32 pages 34.36 Kb

Page 23

PROBLEM: The incline of the treadmill does not change correctly

Idler Roller Bolts

2–3 in.

Remove the three #8 x 3/4" Screws (11) and care- fully pivot the Motor Hood (59) off.

Locate the Reed Switch (71) and the Magnet (47) on the left side of the Pulley (89). Turn the Pulley until the Magnet is aligned with the Reed Switch.

Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If neces- sary, loosen the #8 x 3/4" Truss Head Screw (15), move the Reed Switch slightly, and then retighten the Screw. Reattach the Hood (not shown), and run the treadmill for a few minutes to check for a cor- rect speed reading.

59	11

1/8 in.	47
71	47
Top	89
Top
View

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re- move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the maximum incline level and then return to the minimum level. This will recalibrate the incline system.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.

b. If the walking belt is overtightened, treadmill perfor- b mance may decrease and the walking belt may be- come damaged. Remove the key and UNPLUG

THE POWER CORD. Using the hex key, turn both idler roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

c. If the walking belt still slows when walked on, see the front cover of this manual.

23

Image 23

ProForm PFTL06009.0 user manual PROBLEM The incline of the treadmill does not change correctly

Contents

TACT THE STORE please contact Customer Care QUESTIONS?1CALL-888TOLL-533-FREE-1333 Model No. PFTL06009.0 Serial NoWARNING DECAL PLACEMENT TABLE OF CONTENTSinformed of all warnings and precautions IMPORTANT PRECAUTIONSpre-existing health problems meets all of the specifications described on23. Never insert any object into any opening on the treadmill SAVE THESE INSTRUCTIONSBEFORE YOU BEGIN and scissors ASSEMBLYadjustable wrench rubber malletfreely 1. Make sure that the power cord is unpluggeddo not fully fold the Frame yet overtighten the Nut the Wheel must turnUpright Spacer 88. Be careful not to pinch the Wire Harness 87. Tighten the 3/8 xwith a second Bolt Spacer 82, 3/8 x 4 Bolt 4, and 3/8 Star WasherBolts yet See assembly steps 4 and 6. Firmly tighten the 3/8 x 4 Bolts Hold the receiver so the antenna is oriented 3. Be careful not to pinch the wires. Reattach11. Raise the Frame 52 to the position shown this step is completedTHE PRE-LUBRICATED WALKING BELT OPERATION AND ADJUSTMENTHOW TO PLUG IN THE POWER CORD FEATURES OF THE CONSOLE CONSOLE DIAGRAMHOW TO USE THE MANUAL MODE 1. Insert the key into the console HOW TO TURN ON THE POWERthe key can be pulled from the console, causing not pulled from the console, adjust the position of6. Measure your heart rate if desired 5. Monitor your progress with the displays. The matrix-When you7. When you are finished exercising, remove the key from the console 4. Monitor your progress with the displays. See step 5 on page HOW TO USE A PRESET WORKOUT 1. Insert the key into the console6. When you are finished exercising, remove the key from the console 3. Start the walking belt6. When you are finished exercising, remove the key from the console HOW TO USE THE CUSTOM WORKOUT CENTER1. Insert the key into the console 2. Select the Custom Workout Center6. When you are finished exercising, remove the key from the console HOW TO USE THE WEIGHT LOSS WORKOUT CENTER2. Select a weight loss workout HOW TO USE THE SOUND SYSTEM1. Insert the key into the console HOW TO USE AN IFIT CARD5. When you are finished exercising, remove the key from the console 2. Insert an iFit card and select a workoutTHE OPTIONAL CHEST PULSE SENSOR THE INFORMATION MODEknob is locked in the storage position HOW TO FOLD AND MOVE THE TREADMILLHOW TO MOVE THE TREADMILL HOW TO LOWER THE TREADMILL FOR USEcompatible with GFCI-equipped outlets TROUBLESHOOTINGPROBLEM The power turns off during use PROBLEM The displays of the console do not function properlyPROBLEM The walking belt slows when walked on PROBLEM The incline of the treadmill does not change correctlyPROBLEM SOLUTION EXERCISE FREQUENCY EXERCISE GUIDELINESEXERCISE INTENSITY WORKOUT GUIDELINESKey No. Qty PART LIST-Model No. PFTL06009.0Key No. Qty DescriptionDescription 10 Black Wire, M/FDescription EXPLODED DRAWING A-Model No. PFTL06009.0 R0709A EXPLODED DRAWING B-Model No. PFTL06009.0 R0709A EXPLODED DRAWING C-Model No. PFTL06009.0 R0709A EXPLODED DRAWING D-Model No. PFTL06009.0 R0709A ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT ORDERING REPLACEMENT PARTSLIMITED WARRANTY