| HOW TO TURN ON THE POWER |
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
| Plug in the power cord (see page 10). |
|
|
|
|
| |
| 1 |
|
|
|
|
| ||
|
| Locate the reset/off |
|
|
|
|
| |
| 2 |
|
|
|
|
| ||
|
|
|
|
|
| |||
| circuit breaker near |
|
|
|
|
| ||
|
|
| Reset |
|
| |||
|
|
|
|
|
| |||
|
| the power cord. Make |
|
|
|
| ||
|
|
| Position |
|
| |||
|
| sure that the circuit |
|
|
| |||
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
|
| breaker is in the reset |
|
|
|
|
| |
|
|
|
|
|
|
| ||
|
| position. |
|
|
|
|
| |
|
| Stand on the foot rails of the treadmill. Find the clip | ||||||
| 3 | |||||||
| attached to the key (see the drawing on page 11) | |||||||
| ||||||||
|
| and slide the clip onto the waistband of your |
|
|
| |||
|
| clothes. Next, route the cord attached to the clip | ||||||
|
| under the handgrip pulse sensor, |
|
| and insert the | |||
|
| key into the console. After a moment, the displays | ||||||
|
| and various indicators will light. |
|
| Test the clip by | |||
|
| carefully taking a few steps backward until the |
|
|
| |||
key is pulled from the console. If the key is not pulled from the console, adjust the position of the clip.
HOW TO USE THE MANUAL MODE
1 Insert the key fully into the console.
See HOW TO TURN ON THE POWER above.
2 Select the manual mode.
When the key is in- serted, the manual mode will be selected and the Manual indica- tor will light. If a pro- gram has been
walking. As you exercise, change the speed of the walking belt as desired by pressing the Speed in- crease and decrease buttons. Each time a button
is pressed, the speed setting will change by 0.1 mph; if a button is held down, the speed setting
will change in increments of 0.5 mph. To change the speed setting quickly, press the Quick Start but- tons.
| To stop the walking belt, press the Stop button. |
|
|
| |
| The Time/Pace display will begin to fl | ash. To | |||
| restart the walking belt, press the Start | button or | |||
| the Speed increase button. |
|
|
| |
| Note: The first time the treadmill is used, observe |
|
|
| |
| the alignment of the walking belt, and align the |
|
|
| |
| walking belt if necessary (see page 27). |
|
|
| |
4Change the incline of the treadmill as desired. |
|
|
| ||
| To change the incline of |
|
|
|
|
|
|
|
|
| |
| the treadmill, press the |
|
|
|
|
| Incline buttons. Each time |
|
|
|
|
| a button is pressed, the |
|
|
|
|
|
|
|
| ||
| incline will change by |
|
|
|
|
|
|
|
|
| |
| 0.5%. Note: After the but- |
|
|
| |
| tons are pressed, it may take a moment for the |
|
|
| |
| treadmill to reach the selected incline setting. |
|
|
| |
| Follow your progress with the matrix, the |
|
|
| |
5 |
|
|
| ||
training zone bar, and the displays. |
|
|
| ||
|
|
|
| ||
The matrix —When the
manual mode or the iFIT.com mode is se- lected, the matrix will display a
dicators around the track
will light in succession until the entire track is lit. The track will then darken and the indicators will again begin to light in succession.
selected, press the Program Select button repeat- edly to reselect the manual mode.
3 | Press the Start button or the Speed increase | ||||
button to start the walking belt. | |||||
| |||||
| A moment after the but- |
| |||
|
| ||||
| ton is pressed, the |
|
| ||
| walking | belt will begin to |
| ||
| move at 1 mph. Hold |
|
| ||
| the handrails | and begin |
| ||
|
| ||||
The training zone bar The training zone bar shows the approximate intensity level of your ex- ercise. For example, if three to six indicators in the bar are lit, the bar shows that your pace is ideal for fat burning.
— |
12
