R

I. Door Installation

To install door:

1.Carefully remove door from packaging.

2.Line up hinges with hinge pins on appliance body, and slide door down until it sits securely on pins. Figure 21.1.

3.If door is plated, be sure to clean all plated surfaces and glass with a glass cleaner to ensure all oils are removed before your first burn.

4.Remove all labels from glass before burning appliance.

To adjust latches:

1.

Close door securely.

2.

Place rod in slot on the bracket on the door and close

 

latch.

3.

Latch must close tightly enough to ensure an airtight

 

seal between the door and the body of the appliance. To

 

increase tension on the latch, turn the rod clockwise a few

 

turns, then attempt to close the latch, until it is snug. Do not

 

overtighten; you should be able to close the latch with your

 

hand. Figure 21.2.

4.

After adjusting the latch, place a Phillips head screw driver

 

in the end of the rod, and tighten the nut with a wrench.

 

This will maintain the correct tension on the rod and latch.

Hinge Pin

Hinge

Figure 21.1

Rod and nut

Rod and nut

Figure 21.2

CB 1200 Pellet Stove

J. Thermostat Installation

1. A 12 volt AC thermostat is required to operate this pellet appliance. You may use the included wall mount thermo- stat or purchase an optional programmable thermostat or remote control. It is equipped with an adjustable heat anticipator. The current rating is .05 amps. The anticipator needs to be adjusted to the lowest setting available.

2.When mounting a thermostat on a wall, be sure to follow your thermostat installation instructions carefully.

NOTE: Thermostat must be mounted level for accurate readings. The thermostat should be mounted on an inside wall and not in direct line with the appliance convection air.

NOTE: If the thermostat is located too close to the appliance, you may need to set the temperature setting slightly higher to maintain the desired temperature in your home.

3.There is a 4 screw terminal block located on the back lower left corner of the stove directly above the power cord inlet. The center 2 screws are for the thermostat wires.

Power Outlet

Terminal Block.

Center 2 screws for

Thermostat Wires

Figure 21.3

Caution

Shock hazard.

• Do NOT remove grounding prong from plug.

Plug directly into properly grounded 3 prong receptacle.

Route cord away from appliance.

Do NOT route cord under or in front of appliance.

September 21, 2006

7014-082B

Page 21

Page 21
Image 21
Quadra-Fire CB1200 Door Installation, CB 1200 Pellet Stove Thermostat Installation, To install door, To adjust latches

CB1200 specifications

The Quadra-Fire CB1200 is a highly efficient and versatile wood-burning stove that stands out in the market for its innovative features and robust performance. With a focus on both functionality and aesthetics, the CB1200 aims to provide a comfortable, efficient heating solution while enhancing the beauty of any living space.

One of the main features of the Quadra-Fire CB1200 is its powerful heating capability. It boasts a maximum heat output of up to 80,000 BTUs, making it suitable for heating large areas within homes and cabins. The unit can efficiently heat spaces up to 2,500 square feet, offering reliable warmth even in the coldest climates. This impressive output is complemented by an extended burn time, allowing for longer periods between refueling, which adds convenience for users.

The CB1200 comes equipped with Quadra-Fire's renowned Advanced Combustion Technology. This cutting-edge system improves the efficiency of the fire by maximizing the combustion of gases and particles, leading to a cleaner burn with reduced emissions. This not only enhances the stove's overall performance but also provides a more environmentally friendly heating solution.

Another notable characteristic of the CB1200 is its user-friendly design. The large, glass door provides an excellent view of the fire, creating a warm and inviting ambiance while ensuring easy monitoring of fuel levels. The stove features a convenient ash pan for effortless cleanup, and the adjustable airflow control allows users to customize the burn intensity to suit their heating needs.

In addition to its performance features, the CB1200 is designed with durability in mind. Constructed from high-quality materials, it is built to withstand the rigors of regular use. The unit also offers various finishing options, enabling homeowners to select a style that complements their décor.

The Quadra-Fire CB1200 combines efficiency, beauty, and convenience, making it an exemplary choice for anyone seeking a wood-burning stove. With its impressive heating capabilities, advanced combustion technology, and user-friendly features, the CB1200 is designed to provide lasting comfort and satisfaction for its users, making it a worthwhile investment for any home.