CB 200 Pellet Stove | R |
|
|
| Reference Materials |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| E |
|
|
|
|
| |
| Component Function & Location |
| When describing the location of a component, |
| |||||||
|
|
|
|
| |||||||
|
|
|
| it is always AS YOU FACE THE FRONT OF |
| ||||||
A.11 |
|
|
|
|
|
| |||||
1. Control Box |
|
|
|
|
| THE APPLIANCE. |
|
| |||
| a. The control box is located under a small cover in the |
|
|
|
|
| |||||
7. | Heat Exchangers |
|
| ||||||||
| right rear corner of the inside of the hopper. |
|
| ||||||||
| b. There is a light located inside of the control box. The | The heat exchangers transfer hot air from the exhaust system | |||||||||
| into convection air. Lift the stove top to access the heat | ||||||||||
| internal light will turn green when the appliance has | ||||||||||
| reached a temperature of 200οF (93°C) in the firepot | exchangers. There are 2 clean out rods located under the | |||||||||
| and will turn red when it reaches 600oF (315°C). | heat exchangers. |
|
| |||||||
| c. There is also an internal blue light located in the upper | 8. Heat Output Switch |
|
| |||||||
| left corner of the control box. | When you plug in the | The heat output switch is located on the upper right side panel. | ||||||||
| appliance the blue light will automatically start blinking | The function of the heat ouput switch is to regulate the burn | |||||||||
| 1 blink every 10 seconds for the first 60 seconds and | rates; low, medium, and high settings. | |||||||||
| then will stop. |
|
|
|
| 9. | Igniter |
|
| ||
|
|
|
|
|
|
|
|
| |||
| NOTE: |
|
|
|
| The igniter is mounted on the base of the firepot. Combustion | |||||
| Do NOT open the control box. This will void the |
| air travels over the red hot igniter creating super heated air | ||||||||
| warranty. If you need to plug in or remove the control |
| that ignites the pellets. |
|
| ||||||
| box you must first unplug the appliance. |
|
| 10. Junction Box And Wiring Harness | |||||||
|
|
|
|
|
|
| The junction box is located on the right side of the appliance, | ||||
| 2. Convection Blower |
|
|
| |||||||
|
|
|
| behind the interior shield. The junction box and wiring harness | |||||||
| The convection blower is mounted at the bottom rear of the | are replaced as one component. | |||||||||
|
|
|
|
|
| ||||||
| appliance. There are 2 impellers, one on each side of the | 11. | Power Supply |
|
| ||||||
| motor. The convection blower pushes heated air through the | The power outlet is located on the back of the appliance, | |||||||||
| heat exchange system into the room. |
|
| ||||||||
|
|
| lower right corner. Check the wall receptacle for 120 volt, | ||||||||
| 3. Exhaust Blower |
|
|
|
| ||||||
|
|
|
|
| 60 Hz (standard current). Make sure the outlet is grounded | ||||||
| The exhaust blower is mounted on the lower left side on | and has the correct polarity. | A good surge protector is | ||||||||
| recommended. |
|
| ||||||||
| rear of appliance. The exhaust blower is designed to pull |
|
| ||||||||
|
|
|
|
|
| ||||||
| the exhaust from the appliance and push it out through the | 12. | Red Call Light |
|
| ||||||
| venting system. |
|
|
|
| The red call light is on the front of the junction box, next to the | |||||
| 4. Feed System |
|
|
|
| ||||||
|
|
|
|
| reset button. The function of the red call light is to indicate | ||||||
| The feed system is located in the hopper under the feed | that the thermostat is calling for heat. | |||||||||
|
|
|
|
|
| ||||||
| motor cover box on the left side of the appliance and can | 13. | Reset Button |
|
| ||||||
| be removed as an entire assembly. The assembly includes | The reset button is located on the right side of the apppliance | |||||||||
| the feed motor, mounting bracket, bearing and feed spring | ||||||||||
| next to the red call light. The function of the button is to | ||||||||||
| (auger). The hollow feed spring (auger) pulls pellets up the | ||||||||||
| momentarily open the thermostat circuit, which restarts the | ||||||||||
| feed tube from the hopper area and drops them down the | ||||||||||
| system. |
|
| ||||||||
| feed chute into the firepot. |
|
|
|
|
| |||||
|
|
|
| 14. | Thermocouple |
|
| ||||
| 5. Firepot |
|
|
|
|
|
| ||||
|
|
|
|
| The thermocouple is located on top of the firepot inside | ||||||
| The firepot is made of high quality ductile iron and has a | ||||||||||
| the thermocouple cover (ceramic protection tube). The | ||||||||||
| cleaning | ||||||||||
| thermocouple sends a millivolt signal to the control box | ||||||||||
| cleaning when you pull out the rod. Be sure that the floor | ||||||||||
| indicating the preset temperatures of the green and red lights | ||||||||||
| returns to a completely closed position or your appliance will | ||||||||||
| have been obtained. |
|
| ||||||||
| not operate properly. |
|
|
|
|
|
| ||||
|
|
|
|
| 15. | Thermostat |
|
| |||
| 6. Fuse |
|
|
|
|
|
| ||||
|
|
|
|
| The appliance is designed to run on a 12 volt AC thermostat. | ||||||
| The fuse is located on the front of the junction box on the | ||||||||||
| The heat anticipator should be set on the lowest setting | ||||||||||
| right side of the appliance. The fuse will blow should a short | ||||||||||
| available. |
|
| ||||||||
| occur and shut off power to the appliance. |
|
|
|
| ||||||
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||
Page 34 |
|
| September 21, 2006 | ||||||||
