CB 1200 Pellet Stove

R

C. Tools And Supplies Needed

Tools and building supplies normally required for installation, unless installing into an existing masonry fireplace:

Reciprocating Saw

Safety Glasses

Channel Locks

Framing Square

Hammer

Electric Drill & Bits (1/4”)

Phillips Screwdriver

1/4” Self-Tapping Screws

Tape Measure

 

Plumb Line

May also need:

Level

Vent Support Straps

Framing Material

Venting Paint

Hi-temp Caulking Material

 

Gloves

 

D. Measuring Standards

1.Pipe measurements are from center line to center line.

2.Vertial terminations are measured to top of pipe.

Measure vertical

clearances from

this surface

Measure horizontal

clearances from

this surface

Figure 6.1

WARNING

Inspect appliance and components for damage. Damaged parts may impair safe operation.

•Do NOT install damaged components.

•Do NOT install incomplete components.

•Do NOT install substitute components.

Report damaged parts to dealer.

E. Inspect Appliance & Components and Pre-Use Check List

1.

 

Place the appliance in a location near the

 

 

final installation area and follow the proce-

 

 

dures below:

2.

 

Open the appliance and remove all the parts

 

 

and articles packed inside the Component

 

 

Pack. Inspect all the parts and glass for ship-

 

 

ping damage. Contact your dealer if any irregu-

 

 

larities are noticed.

3.

 

All safety warnings have been read and fol-

 

 

lowed.

4.

 

This Owner’s Manual has been read.

5.

 

Floor protection requirements have been met.

6.

 

Venting is properly installed.

7.

 

The proper clearances from the appliance and

 

 

chimney to combustible materials have been

 

 

met.

8.

 

The masonry chimney is inspected by a profes-

 

 

sional and is clean, or the factory built metal

 

 

chimney is installed according to the manufac-

 

 

turer’s instructions and clearances.

9.

 

The chimney meets the required minimum

 

 

height.

10.

 

All labels have been removed from the glass

 

 

door.

11.

 

Plated surfaces have been wiped clean, if

 

 

applicable.

12.

 

Thermostat or remote has been installed.

13.

 

A power outlet is available nearby.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions:

•Installation and use of any damaged appliance.

•Modification of the appliance.

•Installation other than as instructed by Hearth & Home Technologies.

•Installation and/or use of any component part not approved by Hearth & Home Technologies.

•Operating appliance without fully assembling all components.

•Operating appliance without legs attached (if supplied with unit).

•Do NOT Overfire

Or any such action that may cause a fire hazard.

Page

7014-082B

September 21, 2006

Page 5 Page 7
Page 6
Image 6
Quadra-Fire CB1200 owner manual CB 1200 Pellet Stove Tools And Supplies Needed, Measuring Standards
Page 5 Page 7

CB1200 specifications

The Quadra-Fire CB1200 is a highly efficient and versatile wood-burning stove that stands out in the market for its innovative features and robust performance. With a focus on both functionality and aesthetics, the CB1200 aims to provide a comfortable, efficient heating solution while enhancing the beauty of any living space.

One of the main features of the Quadra-Fire CB1200 is its powerful heating capability. It boasts a maximum heat output of up to 80,000 BTUs, making it suitable for heating large areas within homes and cabins. The unit can efficiently heat spaces up to 2,500 square feet, offering reliable warmth even in the coldest climates. This impressive output is complemented by an extended burn time, allowing for longer periods between refueling, which adds convenience for users.

The CB1200 comes equipped with Quadra-Fire's renowned Advanced Combustion Technology. This cutting-edge system improves the efficiency of the fire by maximizing the combustion of gases and particles, leading to a cleaner burn with reduced emissions. This not only enhances the stove's overall performance but also provides a more environmentally friendly heating solution.

Another notable characteristic of the CB1200 is its user-friendly design. The large, glass door provides an excellent view of the fire, creating a warm and inviting ambiance while ensuring easy monitoring of fuel levels. The stove features a convenient ash pan for effortless cleanup, and the adjustable airflow control allows users to customize the burn intensity to suit their heating needs.

In addition to its performance features, the CB1200 is designed with durability in mind. Constructed from high-quality materials, it is built to withstand the rigors of regular use. The unit also offers various finishing options, enabling homeowners to select a style that complements their décor.

The Quadra-Fire CB1200 combines efficiency, beauty, and convenience, making it an exemplary choice for anyone seeking a wood-burning stove. With its impressive heating capabilities, advanced combustion technology, and user-friendly features, the CB1200 is designed to provide lasting comfort and satisfaction for its users, making it a worthwhile investment for any home.
Top Page Image Contents