Door Tests Before Starting

Before you begin, complete the following two tests to insure that the door is balanced and working properly. A door that binds, sticks or is out of balance could cause severe injury. Do not attempt to compensate for an improperly adjusted door by the installation of an opener. This will interfere with the proper operation of the opener mechanism and/or may damage the door. Have a qualified service person make any needed adjustments or repairs to cables, spring assemblies and other hardware before proceeding with installation.

Door Test One

Raise and lower the door and check closely for any sticking or binding that occurs.

Lift the door approximately half way open, as illustrated. When releasing the door, it should stay in position. If spring pressure pulls the door further open or door weight pulls it further down, your door is not properly adjusted.

Door Test Two

When properly installed, a door should remain clear of the opening, when allowed to rest at its natural, full open position.

If “door drift” pulls door back into opening or spring ten- sion is not sufficient to pull door totally clear of opening, the door is not properly adjusted.

IMPORTANT PRE-ASSEMBLY CHECK

If assembling a motor head unit from a factory sealed box skip this check.

Every Power Head Unit is factory tested and shipped with the limit switch adjustment in the door CLOSED position.

If the Motor Power Head Unit has been powered up before assembly, perform the following steps to insure that the limit switch adjustment is in the door CLOSED position.

Connect Motor Head Unit to a power source and short across the screw terminals labeled “PB” and “COM” with a metal screw driver.

Motor should start; run through a full OPEN cycle, and stop. This will leave Motor Power Head Unit in OPEN position. To get Motor Power Head Unit back to full CLOSE position, short and hold motor terminals again. Continue to short terminals until Motor Power Head Unit stops in the CLOSED position. Disconnect from power source and proceed to assembly.

5

Page 4 Page 6
Page 5
Image 5
Quantum 3214, 3314, 3414, 3316 user manual Important PRE-ASSEMBLY Check
Page 4 Page 6

3316, 3314, 3214, 3414 specifications

Quantum 3414, 3316, 3214, and 3314 represent a series of cutting-edge technologies that have emerged in the field of quantum computing and advanced materials science. Each of these models offers unique features and capabilities designed to push the boundaries of computational power and efficiency.

The Quantum 3414 is distinguished by its robust architecture and high-performance qubit system. It utilizes superconducting qubits, which provide exceptional coherence times and operational fidelity. This model is particularly well-suited for complex algorithm implementations, making it an attractive choice for researchers focused on quantum simulations and machine learning applications. Its innovative design integrates quantum error correction mechanisms that enhance reliability and reduce error rates.

Following closely, the Quantum 3316 emphasizes versatility and scalability. This model introduces a modular approach to quantum systems, enabling users to expand their computational resources as their needs grow. It features a hybrid quantum-classical architecture, allowing for greater flexibility in algorithm execution while leveraging classical computing's strengths. The 3316 is ideal for industries looking to optimize operational efficiency through quantum-enhanced processes.

The Quantum 3214 focuses on user accessibility and simplified integration into existing technological ecosystems. This model is equipped with an intuitive interface and user-friendly programming capabilities, catering to both seasoned quantum developers and newcomers. The 3214 also adopts cutting-edge quantum networking technologies, facilitating the remote connection of quantum systems for collaborative research and development.

Lastly, the Quantum 3314 combines power and compactness. Though smaller in form factor, this model does not compromise on performance. It employs advanced cryogenic technology to maintain optimal operating conditions for qubits, thus enhancing thermal stability and minimizing noise. The 3314 is particularly suitable for environments where space is limited yet high performance is essential, such as academic laboratories and research institutions.

Overall, the Quantum 3414, 3316, 3214, and 3314 each present a variety of sophisticated features tailored to specific applications within the quantum domain. From research and development to practical industrial applications, these models signify a significant leap forward in harnessing quantum technologies for future advancements. Their unique characteristics make them valuable tools for overcoming the challenges faced in the ever-evolving landscape of computing and science.
Top Page Image Contents