Using the TV’s Menu System
0 Go Back
1 Signal Strength
2 Channel Search
3 Software Upgrade
4 Signal Source
5 Video Input Source
6 Auto Tuning
7 Special Features
8 Ethernet Setup
Main Menu 
Connections
Front Input
Use this screen if you have misplaced your remote control and need a way to tune to a different antenna or to go to the video inputs. Use the arrows to highlight the rectangle then press OK or
You can select a source from the available signal sources. Press OK to continue.
Signal Source
The Signal Source menu allows you to choose the source from which you would like the signal to come: Cable Input, Antenna Input, or Video Inputs. The same can be accomplished using the component buttons if you’ve set up Auto Tuning on the remote or by pressing the INPUT button. But, if you misplace the remote, this feature gives you another way to tune to a signal source.
0 Go Back
1 Signal Strength
2 Channel Search
3 Software Upgrade
4 Signal Source
5VideoS gnal InputType Setup
6 Auto Tuning
7 Special Features
8 Ethernet Setup
Main Menu 
Connections
Select the Input 2 video source:
Component Video (Y PB PR)
Composite Video
The component video (Y PB PR) connectors on the TV can be changed to accept composite video instead. When using composite video, connect the yellow RCA cable to the Y/VIDEO connector on the TV.
You can select the Air/Cable setting for Antenna A and Antenna B. Press OK to continue.
Video Input Setup
The Video Input Setup screen lets you choose which type of connection you’re using for the Input 2 jack on the back of the TV. If you decide to change the connection, you need to go back into the Video Input Setup screen and select the corresponding option.
0 Go Back
1 Signal Strength
2 Channel Search
3 Software Upgrade
4 Signal Source
5 Video Input Setup
6 Auto Tuning
7 Special Features
8 Ethernet Setup
Main Menu 
Connections
Select which input or channel should be automatically tuned when a button listed below is pressed on the remote control.
VCR | AUDIO (Audio Receiver/Amp) |
Front Input | Front Input |
VCR2 (AUX default) | RCA SAT2 |
Front Input | Front Input |
DVD |
|
Front Input |
|
Front Input
Press OK to select the channel or input that is tuned when the VCR key is pressed on the remote.
Auto Tuning
This menu lets you specify the various components you have connected to your TV. It lets you program a component button on the remote control (AUX or DVD) so that pressing the button automatically turns on the TV and turns the TV to the correct Video Input Channel (go to Chapter 3 for detailed information).
Notes: The AUX button by default is set up for a second RCA VCR. If you need to reprogram the AUX button, or instead want to program the VCR button, use the 2001 code. Then use the VCR2 option in the auto tuning menu to set auto tuning.
The RCA SAT2 option doesn’t have a function for your remote.
0 Go Back
1 TextInitialhereChannel
2 Initial Volume
3 Maximum Volume
4 CableCARD Tools
5 Remote Setup
Main Menu 
Connections 
Special Features
Select what should occur when power is restored to the TV:
Off: Initial Channel is disabled
On: Go to last input or channel selected
On: Go to Cable Input
Channel 999
Note: An Initial Channel setting of "On" will be enabled only when the TV is plugged back in or electricity is otherwise restored to the TV. Initial Channel is not enabled from the turning on of the TV with the remote or front buttons.
Press or to point to an option, then press OK to select it. Press to return to the menu.
Special Features
Initial Channel and Initial Volume are two special features that are mostly intended for commercial/retail use.
Initial Channel You can select the tuner and channel or input that your TV tunes to each time the TV is turned on by plugging it back in.
Initial Volume This feature works only if the Initial Channel feature is set to On. Select the volume level that you want when the TV is turned on.
Maximum Volume This feature is intended to stop the volume from being turned up too loudly. Set the volume at the loudest level you would want to hear.
Chapter 4 | 51 |
