Rheem RS47-21BP, RS80-42BP Roof Preparation, Supporting Structure installation

Models: RS47-21BP RS80-42BP

1 40
Download 40 pages 48.13 Kb
Page 19
Image 19

Roof Preparation

This section contains instructions for correct installation of the system. Complete the procedures in the order listed.

NOTICE: The storage tank will be parallel to rafters of trusses for side- pitch mount and at a right angle for all other mounts.

NOTICE: Supporting rafters may be either 16” or 24” on center. Runners will not be equally spaced on 16” on-center rafters. See Figure for “Wood Runner Detail”.

NOTICE: Double check the placement of the runners over the rafters or trusses before drilling holes.

Refer to the checklist for necessary roof modifications on page 12.

Install supports for Fragile Tile Roof

The system may be installed directly on most roof types if the roof is in good condition with adequate drainage.

For other types of roofs, do the following:

Clear area of roofing material from top of roof to lower edge of roof with 2'

clearance on each side (refer to Figure below) set aside for reinstallation.

Install waterproof material over cleared area.

Fully seal and waterproof new material.

Continue with section; Supporting Structure Installation.

Fragile Tile Roof

Supporting Structure installation

NOTICE: You may want to pre- drill runners with pilot holes to avoid splitting runners with lag screws.

Refer to the appropriate section listed below for installation procedures:

•Standard Installation: Page 19

•Metal / Sturdy Tile Installation: Page 20

•Frame Installation: Page 21

Standard Installation

1.Mark supporting rafter/truss and bearing-wall locations on roof.

2.Place four 2" x 4" x 8' 4” redwood, treated-wood or Unistrut runners parallel down roof slope over marked rafters or trusses.

•For standard installation, runners must be placed within 3’ of roof ridge

•For roof-ridge mounts, place top of runners at roof ridge

3. Drill each runner in center and 6" from

runner ends and attach to rafters or trusses with 5/6" x 6" lag screws and washers.

4.Flash and seal all roof penetrations.

5.Position Collector Extrusion so that flat vertical edge is toward roof ridge

6.Level the Extrusion using a spirit level and shims After leveling, raise the hot pipe side of the extrusion by 1/2” per collector to ensure correct operation of the system (eg. For a 2 collector system, raise the hot pipe side of the extrusion by 1”).

7.Mount the Extrusion to each runner using 5/16" x 2” lag screws or Unistrut bolts.

8.Continue with Collector Installation, page 23.

19

Page 19
Image 19
Rheem RS47-21BP, RS80-42BP installation instructions Roof Preparation, Supporting Structure installation

RS47-21BP, RS80-42BP specifications

The Rheem RS47-21BP and RS80-42BP are innovative water heater solutions designed to meet the diverse needs of modern households. These models incorporate advanced technologies to enhance efficiency, performance, and user convenience.

The Rheem RS47-21BP is a 47-gallon heat pump water heater that provides a strong balance between performance and energy savings. One of its standout features is its impressive energy efficiency rating. This model utilizes heat pump technology harnessing ambient heat from the air to heat water, drastically reducing energy consumption compared to traditional electric water heaters. This results in lower utility bills and a smaller carbon footprint, making it an environmentally conscious choice.

On the other hand, the RS80-42BP is a larger 80-gallon heat pump water heater suitable for families with higher hot water demands. It offers a similar energy-efficient operation as the RS47-21BP but with an increased capacity. This model is perfect for households that require a reliable supply of hot water for multiple simultaneous uses, such as showers, dishwashing, and laundry. The unit's size is designed to cater efficiently to larger families or higher demand scenarios, making it an ideal choice for busy homes.

Both models are equipped with advanced smart technology, allowing the user to monitor and control the water heater remotely through a smartphone application. This feature provides real-time data on water usage and energy consumption, empowering users to manage their hot water needs proactively. Furthermore, the intuitive interface makes it easy to adjust settings, helping households maximize efficiency.

Additionally, Rheem has incorporated protective features in both models, including an intelligent self-diagnostic system that assists in troubleshooting. The LED display offers clear indications of operational status, making maintenance straightforward. Both units come with durable construction, designed to resist corrosion and prolong their lifespan.

Overall, the Rheem RS47-21BP and RS80-42BP represent the forefront of water heating technology, combining efficiency, smart technology integration, and ample capacity. These water heaters are not only reliable but also contribute significantly to energy savings, catering to both small and large household needs effectively.