Manuals / Ricoh / Computer Equipment / Printer

Ricoh VT1730 manual Shifting the image to the right or left

Models: VT1730

1 63

Download 63 pages 24.03 Kb

Page 26

Shifting the image to the right or left

AdjustingThe Image Position

Shifting the image to the right or left

1.Press down the feed roller pressure lever.

IJ If you do not press down the feed roller pressure lever, the top sheet of papermay be misfed.

2.	If the top sheet of paper		is caught by	I
2.	If the top sheet of paper		is caught by
	the feed	roller, remove the paper and
	reinsert	it. Then, lift the	feed roller
	pressure	lever.

3.Turn the side plate fine adjustment dial as shown in the illustration.

CJ Before installingpaper, make sure that the table is positioned in the center by referring to the indicator.

O The image position can be shifted up to 10 mm, 2/5” each way.

OPERATION

I

25

Image 26

Ricoh VT1730 manual Shifting the image to the right or left

Contents

PRIPORT VT1730 Operating InstructionsMAJOR COMPONENTS Machine ExteriorOperation Panel = KeysPage Environments To Avoid INSTALLATION REQUIREMENTSMachine Environment Optimum environmental conditionsPower Connection Access To The MachineSUPPLYING THE MASTER ROLL, INK, AND TAPE Caution When you open or close the topor hands against the switch actuator Supplying The Master Roll5. Insert the leading edge of the master roll under the feed roller SUPPLYING THE MASTER ROLL, INK, AND TAPE 9. Remove the cut-off portion of the master roll10. Close the top cover Supplying The Master RollSupplying Ink O Do not remove the seal from the spout of the ink pack5. Slide in the ink pack holder 5. Install a ink pack as shown in the figure6. Press the setting lever green tab B until it clicks 7. Close the ink coverSuppiyl“ngTape For The Tape Dispenser O@ion OptionSupplying Tape For The Tape Dispenser SUPPLYING THE MASTER ROLL, INK, AND TAPESUPPLYING THE MASTER ROLL, INK, AND TAPE Supplying Tape For The Tape D~penser OptionOPERATION Cautions For Printing PaperCautions When Using The Document Feeder 1 mmPreparation For Printing Preparation For PrintingLoading paper OPERATION4. Place the paper on the paper feed table 2. Move the paper delivery end plate to match the print paper size Setting up the paper delivery table1. Open the paper delivery table 3. Move the paper delivery side plates to match the print paper sizeOPERATION lbc-&55iih4. Adjust the paper delivery rollers to match the paper size Preparation For PrinthqStandard Printing 4. Press the Master Making key OPERATION 7. Remove the prints from the paper delivery tableStandard Printing 2. Press down the feed roller pressure lever Restoring The Paper Feed And Paper Delivery Tables1. Turn off the main switch 3. Remove the paper from the paper feed table5. Move the paper delivery end plate to its original position Adjusting The Image Position Shifting the image position forward or backwardShifting the image to the right or left P--V 4. Adjust the paper delivery rollers to the print paper positionAdjusting The Image Position OPERATIONAdjusting The Image Density Changing The Printing Speed To Stop The Machine During A Printing Run Making Master And Prints Automatically Making Master And Prints AutomaticallyGroup Printing From The Same Original Class Mode 5. With the Number keys, enter the desired number of sets 6. Turn on the power Sw tch of the tape dispenser optionGroup Printing From The Same Original Class Mode 8. Press the Print Start keyGroup Printing From Different Originals Memory Mode Group Printing From Different Originals Memory Mode 9. Turn on the power switch of the optional tape dispenser~ The Auto Cycle indicator will light 6, Press the Enter key again. The memory returns to MemoryPhoto Mode Printing DAILY MAINTENANCE Thermal Head5. Clean the thermal head as follows 1. Open the ADF cover 2. Wipe off the mntact glass with a dry cloth Contact GlassDAILY MAINTENANCE 3. Close the ADF cover1. Open the paper feed table and press Paper Feed RollerDAILY MAINTENANCE down the feed roller pressure leverPaper Delivery Rollers 1. Open the paper delivery table Exit SensorDAILY MAINTENANCE 2. Wipe the exit sensor with a dry clothDrum Clamper TROUBLESHOOTING 1+ +GWHAT YOU SHOULD DO TROUBLESHOOTINGMONITOR Close the ADF oover3. Close the ADF rover mmpletely When The Misfeed Indicator + Lights“ ++ A “ Original TROUBLESHOOTING “ ++ B “ Paper misfeed in paper feed section4. Press the Reset key When The Misfeed Indicator LightsTo prevent paper misfeeds ~ Curled paper IJ Wrinkled or wavy paper 5. Press the Reset key “ ++ c “ MaSter misfeed in master feed section3. Reset the master roll. See page 4. Close the top cover TROUBLESHOOTINGII ++ E “ Paper wrapping around the drum To prevent paper misfeed When a master misfeed occurs in the master eject section TROUBLESHOOTING When a master misfeed occurs on the drum 1. Open the top cover5. Press the Reset key When The Misfeed Indicator Lights“% + G “ Paper misfeed in the paper exit section TROUBLESHOOTING When The Open Cover/Unit Indicator ~Lights When The Open Cover/Unit Indicator LightsWhen The Supply/Exchange Indicators Light When Other Indicators Light Poor Printing OPERATION NOTES OPERATION NOTESGeneral Cautions CAUTIONSOperating Cautions 6. Do not operate the machine with any rovers off 90mmx140 SPECIFICATIONSSPECIFICATIONS Set up 1050mmx612mmx UOmm 41.3” X 24.1“ X 17.3”