PRIPORT VT1730
Operating Instructions
MAJOR COMPONENTS
Machine Exterior
Operation Panel
= Keys
Page
Environments To Avoid
INSTALLATION REQUIREMENTS
Machine Environment
Optimum environmental conditions
Power Connection
Access To The Machine
SUPPLYING THE MASTER ROLL, INK, AND TAPE
Caution When you open or close the top
or hands against the switch actuator
Supplying The Master Roll
5. Insert the leading edge of the master roll under the feed roller
SUPPLYING THE MASTER ROLL, INK, AND TAPE
9. Remove the cut-off portion of the master roll
10. Close the top cover
Supplying The Master Roll
Supplying Ink
O Do not remove the seal from the spout of the ink pack
5. Slide in the ink pack holder
5. Install a ink pack as shown in the figure
6. Press the setting lever green tab B until it clicks
7. Close the ink cover
Suppiyl“ngTape For The Tape Dispenser O@ion
Option
Supplying Tape For The Tape Dispenser
SUPPLYING THE MASTER ROLL, INK, AND TAPE
SUPPLYING THE MASTER ROLL, INK, AND TAPE
Supplying Tape For The Tape D~penser Option
OPERATION
Cautions For Printing Paper
Cautions When Using The Document Feeder
1 mm
Preparation For Printing
Preparation For Printing
Loading paper
OPERATION
4. Place the paper on the paper feed table
2. Move the paper delivery end plate to match the print paper size
Setting up the paper delivery table
1. Open the paper delivery table
3. Move the paper delivery side plates to match the print paper size
OPERATION
lbc-&55iih
4. Adjust the paper delivery rollers to match the paper size
Preparation For Printhq
Standard Printing
4. Press the Master Making key
7. Remove the prints from the paper delivery table
Standard Printing
OPERATION
2. Press down the feed roller pressure lever
Restoring The Paper Feed And Paper Delivery Tables
1. Turn off the main switch
3. Remove the paper from the paper feed table
5. Move the paper delivery end plate to its original position
Adjusting The Image Position
Shifting the image position forward or backward
Shifting the image to the right or left
P--V
4. Adjust the paper delivery rollers to the print paper position
Adjusting The Image Position
OPERATION
Adjusting The Image Density
Changing The Printing Speed
To Stop The Machine During A Printing Run
Making Master And Prints Automatically
Making Master And Prints Automatically
Group Printing From The Same Original Class Mode
5. With the Number keys, enter the desired number of sets
6. Turn on the power Sw tch of the tape dispenser option
Group Printing From The Same Original Class Mode
8. Press the Print Start key
Group Printing From Different Originals Memory Mode
Group Printing From Different Originals Memory Mode
9. Turn on the power switch of the optional tape dispenser
~ The Auto Cycle indicator will light
6, Press the Enter key again. The memory returns to Memory
Photo Mode Printing
DAILY MAINTENANCE
Thermal Head
5. Clean the thermal head as follows
1. Open the ADF cover 2. Wipe off the mntact glass with a dry cloth
Contact Glass
DAILY MAINTENANCE
3. Close the ADF cover
1. Open the paper feed table and press
Paper Feed Roller
DAILY MAINTENANCE
down the feed roller pressure lever
Paper Delivery Rollers
1. Open the paper delivery table
Exit Sensor
DAILY MAINTENANCE
2. Wipe the exit sensor with a dry cloth
Drum Clamper
TROUBLESHOOTING
1+ +G
WHAT YOU SHOULD DO
TROUBLESHOOTING
MONITOR
Close the ADF oover
When The Misfeed Indicator + Lights
“ ++ A “ Original
3. Close the ADF rover mmpletely
TROUBLESHOOTING
“ ++ B “ Paper misfeed in paper feed section
4. Press the Reset key
When The Misfeed Indicator Lights
To prevent paper misfeeds ~ Curled paper IJ Wrinkled or wavy paper
5. Press the Reset key
“ ++ c “ MaSter misfeed in master feed section
3. Reset the master roll. See page 4. Close the top cover
TROUBLESHOOTING
II ++ E “ Paper wrapping around the drum
To prevent paper misfeed
When a master misfeed occurs in the master eject section
TROUBLESHOOTING
When a master misfeed occurs on the drum 1. Open the top cover
5. Press the Reset key
When The Misfeed Indicator Lights
“% + G “ Paper misfeed in the paper exit section
TROUBLESHOOTING
When The Open Cover/Unit Indicator ~
Lights
When The Open Cover/Unit Indicator Lights
When The Supply/Exchange Indicators Light
When Other Indicators Light
Poor Printing
OPERATION NOTES
OPERATION NOTES
CAUTIONS
Operating Cautions
General Cautions
6. Do not operate the machine with any rovers off
SPECIFICATIONS
SPECIFICATIONS
90mmx140
Set up 1050mmx612mmx UOmm 41.3” X 24.1“ X 17.3”